background image

M 9 6 8 7 9 6   R e v. 1 . 1

POP-UP DRAIN

Tighten TAILPIECE 

(4)

 on DRAIN BODY before

installing DRAIN BODY. 

Fig. B.

DRAIN

BODY

7

3

4

2

REMOVE FLANGE

Thread FLANGE 

(1)

counter-clockwise and remove

FLANGE

(1)

and FOAM GASKET 

(2)

from drain

body.

Fig. A.

Thread LOCKNUT 

(3)

 clock-wise to bottom of

drain body. Push GASKET 

(4)

 down against

LOCKNUT

(3).

Fig. B.

Remove CLEAR PLASTIC COVER 

(1)

.

Remove CARDBOARD SPACER 

(2)

 from under

DRAIN POP-UP 

(3)

.

2

2

3

3

1

1

4

Fig. A.

Fig. B.

Fig. A.

Fig. B.

7

5

FLANGE GASKET

Check DRAIN FLANGE in BIDET to ensure that WHITE
FOAM GASKET 

(1)

 is fully compressed and not visible.

Fig. A.

DRAIN

FLANGE

1

WHITE FOAM
GASKET
NOT VISIBLE

Insert LIFT ROD GUIDE

(1)

 and CABLE CONNECTOR 

(2)

through rear hole, making sure SEAL WASHER 

(3)

 is

properly seated. 

Fig. B.

From below slip slot in MOUNTING NUT 

(4)

 over CABLE 

(5).

Thread NUT 

(4)

onto lift rod guide shank to secure ROD

GUIDE

(1)

to bidet. Hand tighten only. 

Fig. B.

1

2

4

5

3

ILLUSTRATION
SHOWN LESS
VALVES

SLOTTED
MOUNTING
NUT

POP-UP ROD ASSEMBLY

TIGHTEN LOCKNUT

1

Fig. A.

Fig. B.

Tighten LOCKNUT 

(1)

firmly with Adjustable

Wrench or Channel Locks.

2

INSTALL DRAIN FROM

BELOW FIXTURE

6

From under side of BIDET
install DRAIN BODY 

(1)

 up

through drain outlet.

Note:

 No plumber’s putty

or caulk is required.
The CABLE ATTACHMENT
POINT 

(2)

 must face towards

the rear of the BIDET.

DRAIN

OUTLET 

Install FOAM GASKET 

(3) 

and

FLANGE 

(4)

 onto drain body

from above BIDET and tighten
FLANGE 

(4)

 firmly.

1

4

3

Содержание Colony/Colony Soft 3475.301







Отзывы: