background image

Certified to comply with ASME A112.18.1M

Installation

Instructions

T M

   0

     1

     2

    3

    4

    

 5

    

 6

    

KITCHEN FAUCETS

2021.6XX

FAUCET INSTALLATION  (ESCUTCHEON OPTIONAL)

Insert supply TUBES 

(1)

 and threaded MOUNTING STUD 

(2)

through center hole of ESCUTCHEON 

(3)

 and sink deck, or selected

sink hole if ESCUTCHEON 

(3)

 is not used.

Make sure black RUBBER GASKET 

(4)

 is properly centered on base.

Orient faucet so that threaded STUD 

(2)

 is centrally located towards

rear of sink, then assemble RETAINER PLATE with GASKET 

(5)

, or

MOUNTING KIT 

(5a)

 and thread LOCKNUT 

(6, 6a)

 onto MOUNTING

STUD 

(2)

 from underside of sink.

Hand tighten LOCKNUT 

(6, 6a)

 and check that rotation of HANDLE 

(7)

from HOT to COLD is centered.  Secure faucet by tightening LOCKNUT

(6, 6a) 

firmly. Spread TUBES 

(1)

 for better access to LOCKNUT 

(6, 6a)

.

If using ESCUTCHEON 

(3)

, thread ESCUTCHEON WING NUTS 

(8)

 onto

studs from underside of sink and hand-tighten.

2

M66240 REV.1.1

Peel off paper backing from WASHER 

(1, 1a)

 and stick WASHER

(1, 1a)

 into  circular groove of the SUPPORT PLATE 

(2, 2a)

.

REAR EDGE

4

4

6

5

3

3a

3a

INSTALL

Place SUPPORT PLATE 

(2, 2a)

 in

center of ESCUTCHEON 

(3, 3a)

with WASHER 

(1)

 visible.

Turn ESCUTCHEON 

(3, 3a)

 over

with notch of SUPPORT

PLATE 

(2, 2a)

 towards rear of

sink, align STUDS 

(4)

 with

outer holes of sink and

place ESCUTCHEON 

(3, 3a)

 onto

deck.  Hole of SUPPORT

PLATE 

(2, 2a)

 must align with 

hole of sink.

FOR MODEL 2021.631 ONLY:

Install ESCUTCHEON 

(3a)

 (as described on the left).

Insert SPRAY HOLDER 

(5)

 through side hole of installed

ESCUTCHEON 

(3a)

, thread WING NUT 

(6)

 to shank of SPRAY

HOLDER 

(5)

 from underside of sink. Center SPRAY HOLDER 

(5)

on ESCUTCHEON 

(3a)

 and secure by tightening WINGNUT 

(6)

.

1

1

1

2

2

3

2a

Install ESCUTCHEON (optional)

REAR EDGE

INSTALL

1

5

5a

5

8

6

6

6a

6a

4

4

7

LOCKNUT

(FAUCETS

LESS SPRAY)

MOUNTING KIT

FOR FTG. WITH 

HAND SPRAY

LOCKNUT

LESS ESCUTCHEON

TOOLS REQUIRED

Phillips Screwdriver

Plumbers' Putty or Caulking

Adjustable Wrench

Channel Locks

Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.

Turn off water at

main supply.

CAUTION

Отзывы: