background image

-6 - FORM NO. 70309B

                           Clarke

®

 

 American Sanders  Operator's Manual - Sander  1600/1600DC - 230V

OPERATOR SAFETY INSTRUCTIONS (cont.)

WARNING: Operating a machine without observing all labels and instructional information could result in

injury or damage.  Read all machine labels before attempting to operate.  Make sure all of the
labels and instructional information are attached or fastened to the machine.  Get replacement
labels and decals from your authorized distributor.

WARNING: Use of this machine as a step or furniture could result in injury or damage.  Do not use this

machine as a step or furniture.  Do not ride on this machine.

WARNING: To avoid injury keep hands, feet and loose clothing away from all moving parts of this

machine.

WARNING: Injury can occur if protective clothing or equipment is not used while sanding.  Always wear safety

goggles, protective clothing, and dust mask while sanding.

WARNING: Injury to operator or bystanders could occur if an abrupt change in floor surface texture is

encountered when using this machine.  Abrupt change in floor surface texture can cause a
sudden pulling motion by this machine.  This sudden pulling motion can result in loss of
control of the machine which could injure the operator or bystanders.  Avoid motions that
could cause machine to cross from a smooth floor surface to a carpeted or rough texture
floor surface   Avoid motions that could allow the machine to come in contact with low
obstacles, such as floor electrical outlets,  door stops or entry molding, etc.

WARNING: Water solutions or cleaning materials used with this type of machine can leave wet areas

on the floor surface.  These areas can cause a dangerous condition for the operator or
other persons.  Always put CAUTION signs near the area being cleaned.

WARNING: Any alterations or modifications of this machine could result in damage to the machine or

injury to the operator or other bystanders.  Alterations or modifications not authorized by
the manufacturer voids any and all warranties and liabilities.

CAUTION:

The machine is heavy.  Get assistance before attempting to transport or move it.

CAUTION:

Use of this machine to clean carpet could cause damage to carpet and injury to operator or
bystanders.  Do not use this machine to clean carpet.

CAUTION:

This appliance is not suitable for picking up hazardous dust.

CAUTION:

This appliance is for dry use only.  It is not to be used or stored outdoors in wet conditions.

MACHINE INTRODUCTION

Sander 1600DC

The Sander 1600DC is a floor sanding machine.  It can also be used for polishing, grinding, buffing and stripping.  The
machine can be used on wood, vinyl, terrazzo or cement floors.

THIS MACHINE IS SUITABLE FOR COMMERCIAL USE.

Содержание 07102A










































Отзывы: