SAFETY INFORMATION
• Read all instructions before beginning. Save these instructions for future use.
• To reduce the risk of fire, electric shock, or injury to persons, pay close
attention to this manual. Stay within its guidelines when using this product.
• All units must be unplugged before installing or servicing in any way.
• Do not route cords or units through walls, doors, windows, or any similar part
of a building structure.
• Do not use if there is any damage to the unit, its lens, and/or power cord’s
insulcation. Inspect periodically.
• The fixture is rated for wet locations (IP65) and can be exposed to rain and
snow. however, do not let unit stand in water or liquid, nor locate where water
can accumulate.
• Secure units with mounting hardware appropriate for the mounting surface.
Do not secure unit or its power cord with staples, nails, or like materials that
may damage insulation.
• Do not attempt to open or service this fixture. None of its parts are
seviceable by the user.
• Do not exceed the specified voltage and current input: 120V AC, 0.4A per
unit.
• If using in conjunction with the LW36-CON controller, do not exceed the
maximum run of thirty units.
• This product has a grounded plug as a safety feature to reduce the risk of
electric shock. Do not cut the plug off or alter it in any way.
• Provide a grounded receptacle for within 5 feet of each fixture’s location. If
using outdoors, outlet(s) must also be GFCI and weatherproof.
• The maximum number of fixtures that can be controlled by the LW36-CON
controller is thirty (30). For any project that requires more than thirty (30)
fixtures, please consult factory.
These products may represent a possible shock or fire
hazard if improperly installed or attached in any way.
Products should be installed in accordance with these
instructions, current electrical codes, and/or the current
National Electric Code (NEC).
When using this product outdoors, basic safety
precautions should always be followed to reduce the risk
of fire, electric shock and personal injury including the
following:
• Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for outdoor use. Receptacles are available having
built-in GFCI protection for this measure of safety.
• Use only outdoor extension cords, such as type SEW,
SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW,
SJEW, SJEOW, SJEOOW, SJTW, SJTOW, or SJTOOW.
This designation is marked in the wire of the extension
cord. Never use with an extension cord unless plug
can be fully inserted.
This unit requires a 120V AC input power. Disconnect
supply power at the source prior to installation.
WARNING
WARNING
WARNING
LED RGB Linear Wall Washer
120V
INSTALLATION INSTRUCTIONS
LLW32-RGB
BEFORE INSTALLATION:
1. Get familiar with the key parts of the LLW48-RGB. See FIGURE 1.
2. Determine number of fixtures to be used and how power will be delivered.
3. Determine mounting method and fasteners required. See FIGURES 4 and 5 on page 4 for details.
4. Determine if signal cable extensions are needed. Fifteen foot signal cable extensions (item number LW36-EC15, sold separately) can be used
when distances between two fixtures exceed 24”. Signal cable extensions can be interconnected to create longer lengths when needed.
Built-in signal cables are IP65 rated for use in damp location use, but cables may not be located where water can stand or accumulate.
5. Determine method of color control.
• Multiple fixtures can be contolled individually (must have access to all units) or synronously (must have access to the first unit only) using built-
in standalone features. To syncronize, all fixtures must be interconnected with their input and output data cables. The first unit will control all
interconnected fixtures. The maximum number that can be interconnected with signal cables is thirty fixtures. See page 2 for details.
• An external controller (DMX-RGB-3, sold separately) can control all interconnected fixtures (up to thirty maximum) to have mixing levels at
your fingertips and/or to use sound activation. See page 3 for details.
• A DMX hardware/software set up with a custom LLW32-RGB adapter cable (made to order, sold separately) is needed. See page 4 for details.
F
B
B
C
D E
I
G
H
A
A
DMX/Signal Input
B
Safety Anchor
C
LED Display
D
UP Button
E Down Button
F
DMX/Signal Output
G
Power Cord
H
Tilt/Angle Adjustment Handles
I
Mounting Brackets
H
I
FIGURE 1
Page 1 of 4
©2016 American Lighting, Inc. REV1745 www.AmericanLighting.com
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
2-1/16”
End View
- 85˚+ 85˚
