American Dryer Corp. ML-78 Phase 7 (DSI) Скачать руководство пользователя | Manualshive

Страница: 14 / 53

background image

10

SECTION III

INSTALLATION PROCEDURES

Installation should be performed by competent technicians in accordance with local and state codes. In the
absence of these codes, the installation must conform to applicable American National Standards: National
Fuel Gas Code ANSI.Z223.1-LATEST EDITION and/or National Electric Code ANSI/NFPA NO. 70-LATEST
EDITION.

A. LOCATION REQUIREMENTS

Before installing the dryer, be sure the location conforms to local codes and ordinances. In the absence of such
codes or ordinances the location must conform with the National Fuel Gas Code ANSI.Z223.1-LATEST
EDITION.

1. The dryer must be installed on a sound level floor capable of supporting its weight. It is recommended that

carpeting be removed from the floor area that the dryer is to rest on.

2. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

3. The dryer is for use in noncombustible locations.

4. Provisions for adequate air supply must be provided as noted in this manual (refer to Fresh Air Supply in

Section D).

5. Clearance provisions must be made from combustible construction as noted in this manual (refer to Dryer

Enclosure Requirements in Section C).

6. Provisions must be made for adequate clearances for servicing and for operation as noted in this manual

(refer to Dryer Enclosure Requirements in Section C).

7. Dryer must be exhausted to the outdoors (refer to Exhaust Requirements in Section E).

8. Dryer must be located in an area where correct exhaust venting can be achieved as noted in the manual

(refer to Exhaust Requirements in Section E).

IMPORTANT: Dryer should be located where a minimum amount of exhaust duct will be

necessary.

«
...
12
13
14
15
16
...
»

Содержание ML-78 Phase 7 (DSI)






















































Отзывы:

Нет отзывов

Похожие инструкции для ML-78 Phase 7 (DSI)

Zander WVM 1080

Бренд: Parker Страницы: 56

Бренд: FERREX Страницы: 20

Бренд: Daewoo Страницы: 12

Бренд: Orbegozo Страницы: 31

Бренд: DAN DRYER Страницы: 2

Бренд: NEO TOOLS Страницы: 31

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 14

Бренд: Haier Страницы: 2

Tiana HW100-HB1297NZP

Бренд: Haier Страницы: 8

XQG50-ABA1100CTX

Бренд: Haier Страницы: 20

HWD100-B14959S8U1

Бренд: Haier Страницы: 40

HWD100-B14876U1

Бренд: Haier Страницы: 32

XQG50-AB1100CTX

Бренд: Haier Страницы: 20

HWD100-BP14959S8

Бренд: Haier Страницы: 32

Бренд: Haier Страницы: 44

Бренд: Haier Страницы: 32

Бренд: Haier Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды