American Dryer Corp. Gas/Steam Models ML-82 Скачать руководство пользователя страница 18

Страница: 18 / 53

It is not necessary to have separate make-up air openings for each dryer. Common make-up air openings are

acceptable. However, they

must be

set up in such a manner that the make-up air is distributed equally to

ALL

the dryers.

EXAMPLE:

For a bank of four (4) dryers, two (2) unrestricted openings measuring 2 feet by 2-1/2 feet

(0.61 meters by 0.76 meters) - 10 square feet (0.93 square meters) - is acceptable.

Allowances

must be

made for remote or constricting passageways or where dryers are located at excessive

altitudes or predominantly low pressure areas.

IMPORTANT:

Make-up air

must be

provided from a source free of dry cleaning solvent fumes.

Make-up air that is contaminated by dry cleaning solvent fumes will result in

irreparable damage to the motors and other dryer components.

NOTE:

Component failure due to dry cleaning solvent fumes will VOID THE WARRANTY.

E. EXHAUST REQUIREMENTS

1. General Exhaust Duct Work Information

Exhaust duct work

should be

designed and installed by a qualified professional. Improperly sized duct

work will create excessive back pressure which results in slow drying, increased use of energy, overheating

of the dryer, and shut down of the burner by the airflow (sail) switches, burner hi-limits, or basket (tumbler)

hi-heat thermostats.

CAUTION:

DRYER

MUST BE

EXHAUSTED TO THE OUTDOORS.

CAUTION: IMPROPERLY

SIZED

INSTALLED

EXHAUST

DUCT

WORK

CAN

CREATE

POTENTIAL

FIRE

HAZARD.

The duct work

should be

laid out in such a way that the duct work travels as directly as possible to the

outdoors with as few turns as possible. Single or independent dryer venting is recommended.

When single drying venting is used the length of duct work from the dryer to the outside exhaust outlet

should not

exceed

15 feet (4.57 meters). The minimum diameter of this duct work

must be

at least

14-inches (35.56 cm). In the case of multiple (common) dryer venting, the distance from the last dryer to

the outside exhaust outlet

should not

exceed

15 feet (4.57 meters). The shape of the duct work is not

critical so long as the minimum cross-sectional area is provided. It is suggested that the use of 90° turns be

avoided; use 30° and/or 45° angles instead. The radius of the elbows

should preferably be

1-1/2 times the

diameter of the duct. Including basket (tumbler) and dryer elbow connections or elbows used for outside

protection from the weather, no more than two (2) elbows

should be

used in the exhaust duct run. If more

than two (2) elbows are used, the cross-sectional area of the duct work

must be

increased.

ALL

duct

work

should be

smooth inside with no projections from sheet metal screws or other obstructions which will

collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be connected.

ALL

duct work joints

must be

taped to prevent moisture and lint from escaping into the building. Inspection

door

should be

installed at strategic points in the exhaust duct work for periodic inspection and clean-out of

lint from the duct work.

All manuals and user guides at all-guides.com

Содержание Gas/Steam Models ML-82






















































Результаты поиска

Содержание Gas/Steam Models ML-82

Отзывы:

Похожие инструкции для Gas/Steam Models ML-82

Бренды по названию

Популярные бренды

American Dryer Corp. Gas/Steam Models ML-82, Руководство по установке

Результаты поиска

Содержание Gas/Steam Models ML-82

Отзывы:

Похожие инструкции для Gas/Steam Models ML-82

Бренды по названию

Популярные бренды