background image

(14) MASTER LEVEL-DISPLAY - The display shows the signal level of the master output on the left and right jack. 
(15) BALANCE CONTROL - Used to adjust how much of the signal is sent to the left and right MASTER OUT jack (31).
(16) STEREO/MONO SWITCH -  Used to set the master output to mono or stereo. If this switch is set to STEREO, the
master signal is sent to the MASTER OUT jacks (31). For mono and bridged operation, set this switch to MONO and 
connect your amplifier with the 3-pin XLR-jacks on the rear panel (BALANCED OUTPUT jacks (34).
(17) MASTER FADER - Adjusts the level of the master output.
(18) EQUALIZER SWITCH - Used to switch the equalizer on or off.
(19) 7-BAND GRAPHIC EQUALIZER - Used to fine-tune the master output. The frequencies are as follows: 60Hz, 150Hz,
400Hz, 1 KHz, 2.4KHz, 8KHz and 16KHz KHz. They can be adjusted by +/- 12 dB.
(20) MIC 1 JACK - You can connect microphones with 6.3mm jack plug or XLR-plug.
(21) BASS/TREBLE - Use these controls to fine-tune the DJ MIC signal. Increase the LOWs by turning the BASS control
to the right. Increase the Hi’s by turning the TREBLE control to the right.
(22) TALKOVER SWITCH - Use this switch if you want to use your microphone.
If the switch is set to ON, all signals but the microphone level are attenuated by 15dB if the microphone is voice-activated.
As soon as you start speaking, the output level is reduced; as soon as you stop speaking, the output level is reset to the 
original level. If the switch is set to TALKOVER, the output signal is attenuated by 15dB. After you stopped speaking, you
must manually set the TALKOVER switch to MICRO OFF. The output level is then reset to the original level. 
(23) MIC 1 LEVEL FADER - Adjusts the microphone volume.
(24) BNC-JACK FOR GOOSENECK LAMP

© American DJ® AUDIO Los Angeles, CA 90058 USA

Specifications subject to change without notice.  XDM-352 User Instructions page 4

Functions (Cont.)

Inputs and Outputs

(25) MIC 2 JACK - Connect your second microphone with 1/4 inch (6.3mm) jack plug here. 
(26) (26A) GND (Ground terminals) - The XDM-352 features two convieniently located grounds. Connect the ground lead
of the turntable with this terminal. This helps to reduce humming and popping noises. 
(27), (28), (29), (30) LINE I PHONO INPUT JACKS - Input jack for CH-1, CH-2, CH-3 and CH-4. Connect turntables
equipped with MM pickup cartridge to PHONO inputs. CD players or Tape Decks should be connected to LINE input. Line
level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE
inputs. Channel 3 can be switched to 2 line inputs or 1 line / 1 phono input by using the LINE 3 / PHONO 3 selector (37).
(31) MASTER OUT - Parallel output of P.A. output. Connect with the input of power amplifier. Make sure that the
STEREO/MONO switch (16) is set to STEREO.
(32) REC OUT - Connect to your recording unit. The REC OUT level is not influenced by the MASTER FADER (17).
(33) BOOTH OUT - Connect your monitor system here.
(34) BALANCED OUTPUT - Balanced output for the master signal. Make sure that the STEREO/MONO switch (16) is set
to MONO.

25

26A

27

28

29

30

31

32

33

26

34

35

37

36

Отзывы: