©
American DJ Supply
®
- www.americandj.com - Warp Tri LED™ Instruction Manual Page 4
©
American DJ Supply
®
- www.americandj.com - Warp Tri LED™ Instruction Manual Page 3
Warp Tri LED™
Precautions
Safety Issue:
This unit may blow the breaker if the maximum allotted
load of 2 amps is reached. If the fuse needs replacement, please see
the fuse replacement guidelines on page 6.
• Be sure the local power outlet match the required voltage of the
unit.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no
user serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-Cord Protection - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they exit from
the fixture. Do not attempt to remove or break off the ground prong
from the electrical cord. This prong is used to reduce the risk of
electrical shock and fire in case of an internal short.
• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
Warp Tri LED™
Operation
Introduction:
The American DJ
®
Warp Tri
LED™
is a LED moon-flower
effect with 18 gobo patterns. This fixture is designed for mobile DJ’s,
clubs, bands, roller rinks and any arena that requires a compact, light
weight, easy to use unit.
Power Supply:
Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ
®
Warp Tri LED™ before attempting operation.
Operation:
After plugging the unit if there is no LED output check
the fuse. If the fuse has not popped, please contact customer sup-
port for further instructions. This fixture features a light weight case
design and an adjustable hanging bracket.
This unit comes with two 3-way multi-operating switch located on the
bottom of the unit. The switch on the right controls the mirror dish,
and the switch on the left controls the gobo. The switches have three
(3) different operating modes; Static, Sound Active, and Auto.
Mirror Control (Right Switch):
Switch in the "I" auto position: Mode 1 - In this mode the mirror dish
will spin continuously in one direction, regardless of the presence of
sound.
Switch in the “0” static position: Mode 2 - In this mode the mirror
dish will remain static. In this mode the unit may be used as a rotat-
ing-gobo projector.
Switch in the “II” sound active position: Mode 3 - In the this mode the
mirror dish will react to sound. Please note that tapping on the unit,
or high pitched sounds may not trigger the unit, the unit is designed
to react to low frequencies (bass). Also note that the music sensitivity
is preset at the factory and may not be changed or adjusted.
Gobo Control (Left Switch):
Switch in the "I" auto position: Mode 1 - In this mode the gobo wheel
will spin continuously in one direction, regardless of the presence of
sound.
Switch in the “0” static position: Mode 2 - In this mode the gobo
wheel will remain static.
Warp Tri LED™
Warranty Registration
The Warp Tri LED™ carries a three year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
If the unit is under warranty you must provide a copy of your proof of
purchase invoice. Please contact American DJ
®
customer support for
a R.A. number.
