American DJ Vizi Roller Beam 2R Скачать руководство пользователя

Страница: 30 / 30

ADJ Products, LLC - www.adj.com - Vizi Roller Beam 2R Instruction Manual Page 58

Model:

Vizi Roller Beam 2R

Voltage: 100~240V, 50/60Hz

Lamp:

Philips® Platinum MSD 2R Discharge

Power Consumption:

210W

Dimensions: 17.5”(L) x 12”(W) x 9.25”(H)

439.7mm x 300mm x 233.4mm

Weight:

16.75 Lbs. / 7.5 kgs.

Colors:

13 Plus White

Gobos:

8 + 6 Spots

Fuse:

Duty Cycle:

None

DMX:

3 DMX Channel Modes: 11 Channels,

13 Channels, or 18 Channels

Sound Active:

Yes

Working Position:

Any Safe, Secure Position

Warranty:

1 Year (365 days)

Please Note:

Specifications and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Vizi Roller Beam 2R

Specifications

Auto Sensing Voltage:

This fixture contains a electronic bal-

last, which will auto sense the voltage when it is plugged into the

power source.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: [email protected]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[email protected] / www.adj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment.

Please turn off all electrical products when they are not in use. To

avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

Содержание Vizi Roller Beam 2R































Результаты поиска

Содержание Vizi Roller Beam 2R

Отзывы:

Похожие инструкции для Vizi Roller Beam 2R

Бренды по названию

Популярные бренды

American DJ Vizi Roller Beam 2R, Инструкция пользователя

Результаты поиска

Содержание Vizi Roller Beam 2R

Отзывы:

Похожие инструкции для Vizi Roller Beam 2R

Бренды по названию

Популярные бренды