background image

ADJ Products, LLC  -  www.adj.com  - Octo Beam RGBW Instruction Manual Page 9

ADJ Products, LLC  -  www.adj.com  - Octo Beam RGBW Instruction Manual Page 8

  Octo Beam RGBW                                         System Menu

ADDR

 - DMX Address Setting

 

via control board -

1.  Press  the  MENU  button  until  “

ADDR

”  is  displayed,  press 

ENTER.
2. “XXX” will now be displayed, “XXX” represents the displayed 

address.  Press  the  UP  or  DOWN  buttons  to  find  your  desired 

address. 
3. Press ENTER to confirm, then connect your DMX controller.

NOTE: If after you connect your DMX controller the unit does not 

fall into DMX mode, press and hold the MENU button for at least 

3 seconds.

CHND

 - This will let select your desired DMX channel 

mode.

1. Press the either the MENU button until “

CHND

” is displayed, 

press ENTER. Either “

1CH

”, “

8CH

” or “

10CH

” will be displayed

2. Press the UP or DOWN buttons to find your desired DMX 

channel mode and press ENTER to confim and exit.

SLND

 - This will let you set unit as a master or slave in a 

master/slave configuration.

1. Press the MENU button until “

SLND

” is displayed, press 

ENTER. Either “

MAST

”, “

SL 1

” or “

SL 2

” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is 

displayed, press ENTER to confim.
NOTE: In a Master/Slave configuration you can set one fixture 

to Slave 1 (SL 1) and then set the next fixture to Slave 2 (SL 2), 

in doing this the fixtures will now have contrast movement to 

each other. 

SHND: SH 0

 

-

 

SH 12

 - Show modes 0 - 12. Show 

mode can run with or without sound active mode on. 

  Octo Beam RGBW                                         System Menu

1.  Press  the  MENU  button  until  “

SHND

”  is  displayed,  press 

ENTER.
2.  “

SH X

”  will  now  be  displayed,  “X”  representing  a  number 

between 0-12 will be displayed. Shows 1-12 are preset shows, 

while “

SH 0

” is random show. Press the UP or DOWN buttons to 

find your desired show.
3. Once you have found your desired show press ENTER, and 

then press and hold the MENU button for at least 3 seconds to 

confirm. 

DIND

 - Dimmer mode. Control the output intensity of each 

light. 

1.  Press  the  MENU  button  until  “

DIND

”  is  displayed,  press 

ENTER.
2. Either “

FULL

” or “LED X” will now be displayed, “X” repre-

senting a number between 1-8. If you select “FULL” all 8 LEDs 

will be full on.
3. You can select 1-8 LEDs and adjust the output intensity to your 

liking. Press ENTER to select your desired LED and use the UP 

and DOWN buttons to adjust the intensity.

SOUN

 - In this submenu you can activate sound active 

mode. 

1.  Press  the  MENU  button  until  “

SOUN

”  is  displayed,  press 

ENTER.
2. Either “

ON

” or “

OFF

” will now be displayed. Press the UP or 

DOWN buttons to select one or the other.   
3. When you have made your selection, press the ENTER, and 

then press and hold the MENU button for at least 3 seconds to 

confirm. 

SENS

 - 

Sound sensitivity control.

Содержание OCTO BEAM RGBW











Отзывы: