background image

V-01 SERIES SPECS

MODEL:                                     V-4001                                                     V-5001                                                   V-6001
Output Power: 

    

2 Channel:        @8ohm 1kHz,THD+N 0.1%;600W        @8ohm 1kHz,THD+N 0.1%;900W           @8ohm 1kHz,THD+N 0.1%;1100W
                         @4ohm 1kHz,THD+N 0.1%;900W        @4ohm 1kHz,THD+N 0.1%;1400W         @4ohm 1kHz,THD+N 0.1%;1800W
                         @2ohm 1kHz,THD+N 0.1%;1400W      @2ohm 1kHz,THD+N 0.1%;2000W         @2ohm 1kHz,THD+N 0.1%;2500W
Bridged Mono: @8ohm 1kHz,THD+N 0.1%;1800W      @8ohm 1kHz,THD+N 0.1%;2600W         @8ohm 1kHz,THD+N 0.1%;3600W
                         @4ohm 1kHz,THD+N 0.1%;2800W      @4ohm 1kHz,THD+N 0.1%;4000W         @4ohm 1kHz,THD+N 0.1%;5000W
Total Harmonic Less then 0.1% (20Hz-20kHz, @ rated Less then 0.03% (20Hz-20kHz, @ rated Less then 0.03% (20Hz-20kHz, @ rated
Distortion          output power, 4 ohms)                           output power, 4 ohms)                            output power, 4 ohms)
(THD+N):
Frequency        ±1dB,1W RMX @ 8ohms,10Hz-40kHz  ±1dB,1W RMX @ 8ohms,10Hz-40kHz    ±1dB,1W RMX @ 8ohms,10Hz-40kHz
Response:        ±.3dB,1W RMX @ 8ohms,20Hz-20kHz ±.3dB,1W RMX @ 8ohms,20Hz-20kHz   ±.3dB,1W RMX @ 8ohms,20Hz-20kHz
Signal to           >100dB                                                  >100dB                                                    >100dB 
Noise Ratio:      “Audio Filter” Weighted;                        “Audio Filter” Weighted;                          “Audio Filter” Weighted; 
Damping           350 @ 8ohm                                          400 @ 8ohm                                             500 @ 8ohm
Factor:
AC Power         32A @ 120V AC @ 4ohms                     45A @ 120V AC @ 4ohms                        53A @ 120V AC @ 4ohms
Current Draw:   16A @ 230V AC @ 4ohms                     23A @ 230V AC @ 4ohms                        27A @ 230V AC @ 4ohms
Dimensions:      3.5” (H) x 19” (W) x 16.2” (D)                 5.25” (H) x 19” (W) x 19” (D)                    5.25” (H) x 19” (W) x 19” (D)
                          8.8 x 48.2 x 41.2cm                              13.2 x 48.2 x 48.2cm                               13.2 x 48.2 x 48.2cm
Weight:              47.4lbs./21.5kgs.                                   79.3lbs./36kgs.                                        83.3lbs./37.2kgs.

Содержание V-01 Plus Series























Отзывы: