AMBROGIO LINE 250 Скачать руководство пользователя страница 29

28

User’s manual

EN

INITIAL START UP – AUTOMATIC MODE

The automatic cycle is started during the initial start-up or after a period of inactivity.

1.  Check that the height of the lawn surface to mow is compatible with the proper functioning of the robot (see “Technical 

Specifications”).

2.  Adjust the cutting height as desired (see “Adjustment of Cutting Height).
3.  Check that the work area has been correctly marked and that there are no impediments to the regular functioning of the robot 

as indicated in the section “Preparation and Marking the Boundaries of the Work Areas” and following sections.

4.  Position the robot inside the charging station.
5.  Press the "ON/OFF" button and wait a few seconds for the robot to turn on completely. Follow the instructions on the display 

and enter the password if prompted.

6.  If starting the robot for the first time, it is necessary to program the settings. However, if starting the robot after a long period 

of inactivity, check that the programmed functions correspond to the actual condition of the lawn to be mowed (e.g. addition 

of a pool, plants, etc.) (See “Programming Mode”).

7.  After a few seconds, the message “CHARGING” will appear on the display.
8.  The robot starts to mow the lawn according to the modes programmed.
9.  Check there are no large puddles after a heavy rain, otherwise the area must be put in order or make sure the robot is in 

"Pause".

ROBOT SAFETY STOP

During use, it may be necessary to stop the robot. In normal conditions, the robot can be stopped with the “STOP” key. In case 

of danger or when performing any maintenance, it is necessary to stop the robot in safe conditions in order to prevent the blade 

from accidently starting. First press the “STOP” button and then the "ON/OFF " button. Disconnect the power plug from the 

electrical outlet.

Important

The robot safety stop is necessary during 

maintenance and repairs (for example, blade 

replacement, cleaning operations, etc.).

To start, proceed as indicated:

 

-

position the robot inside the cutting area;

 

-

press the "ON/OFF" button to turn on the robot and run the 

start-up procedure again.

If  the  robot  is  started  up  outside  of  the  cutting  area,  the  blade 

motor will not start and after briefly searching for the signal, the 

robot will show "OUT OF BORDER" on the display. Press "ON/

OFF", position the robot inside the cutting area and carry out the 

start up procedure again.

10:30

.....................................

......................

GPS

ON/OFF

STOP

AUTOMATIC RETURN TO THE CHARGING STATION

The robot stops the work cycle if the following conditions are verified:

 

-

End of working time: at the end of the working time, the robot automatically returns to the charging station and starts 

operating again according to what has been programmed (see “Programming Mode”).

 

-

Rain:  with  the  function  active,  the  robot  returns  to  the  recharging  station  automatically  and  will  start  working  again  as 

programmed (see "Programming mode").

 

-

Battery to be charged: the robot automatically returns to the charging station.

 

-

Eco Mode: if the sensor detects that the lawn has already been mowed, it automatically returns to the charging station and 

starts operating again according to what has been programmed (see “Programming Mode”).

Содержание LINE 250










































Отзывы: