Ambirad ARO Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 16

Ambirad ARO Series Скачать руководство пользователя страница 12

Figure 11

Priming and adjustment of the pump (Fig.10).

1. Inlet
2. Return
3. Bleed and pressure gauge port
4. Vacuum gauge port
5. Pressure adjustment
6. Nozzle outlet

Trouble shooting checklist

Symptoms

Fault check

Burner will not start

Mains switch not on.

Ensure burner lockout has been reset.

Blown fuse.
Timer/thermostats not made.
Fault in control box or fan motor.

Burner pre-purges and stops

Fault in control box
Photo cell. Seeing the light or faulty.

Burner does not spark during cycle and

Transformer.

stops

Fault in control box.

Burner does not ignite

Dirty ignition electrodes or incorrect setting.
Fault ignition transformer.
Blocked nozzle.
oil solenoid failure.
Oil pressure too low/Check oil supply.
Blocked oil filter.
Excessive combustion air for nozzle
capacity/check air setting
Fault in control box.

Burner ignites and then stops

Faulty nozzle.
Photo-resistor does not ‘see’ flame.
Excessive combustion air for nozzle capacity.
Fault in control box.
Oil pressure too low.
Blocked oil filter.

10

«
...
10
11
12
13
14
...
»

Содержание ARO Series

















Отзывы:

Нет отзывов