Ambient TOUCH LIGHT Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 11

Ambient TOUCH LIGHT Скачать руководство пользователя страница 10

50D0093 Rev 3 May 2005

Page 10 of 11

Ambient Technologies

A Division Of

3.

Slide the button to OFF. The flame should extinguish (the pilot light will remain on).

4.

Slide the button to RS (the center position), then touch the transmitter to turn the system to ON. The main
gas flame should ignite.

5.

Touch the transmitter to turn the system to OFF. The flame should extinguish (the pilot light will remain
on).

TROUBLESHOOTING

Symptom

Causes

Action

1. LED light on
receiver blinking or
battery icon on LCD
on transmitter.
2. LCD display is
blank
3. LCD display shows
“funny” display

1. Low Battery

1. Replace batteries. Change
batteries every 6 months.
2. Check battery installation and
replace batteries.
3. Press Reset button at the back of
the transmitter.

4. Appliance does not
come on after a valid
touch (beep)

1. Wiring / Electrical Connections

1. Slide the switch to ON, if
appliance comes ON, wiring is not
the cause.
2. If appliance does not come on,
check wiring connections.

2. Privacy (DIP) switch setting on transmitter
does not match receiver

1. Make sure the transmitter and
receiver have the same DIP switch
settings.

3. Transmitter measures temperature exceeding
99 degrees Fahrenheit and shows “HI” on LCD

1. Move transmitter to a cooler
place and wait until temperature
drops below 99 degree.

4. Distance between the transmitter and receiver
is more than 20 feet

1. Make sure the operating distance
is less than 20 feet

5. Receiver cannot
receive signal.

1. Receiver is installed in an enclosure

1. Make sure the receiver is not
located inside an enclosure.

WARNING:

Changes or modifications to this unit not expressly

approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.

«
...
8
9
10
11
»

Содержание TOUCH LIGHT












Отзывы:

Нет отзывов