Set Your Ideal Heating Programme
With 3 diff erent options available, choose
the schedule which best suits your lifestyle.
Whether that is all 7 days the same (7day), 5
days and the weekend (5/2), or just 6 days and
just 1 separate day (6/1).
Having initiated the advanced
settings, tap the button
until you reach (6PRG) to set
your programme.
Use the and buttons to set
which programme you require.
The image above indicates a 7 day schedule.
A 5/2 schedule would only show digits 1-5
& a 6/1 schedule would only show digits 1-6.
Use the button to switch off and save
your settings.
Alternatively, you can switch off the heating
schedule altogether - simply choose the option
Programme off when setting.
Create The Perfect Heating Schedule
Please note down the scheduled times prior to beginning
programming.
By default, your Amber-Touch will be set to a 5/2 schedule.
To personalise this schedule: Enter schedule mode by pressing
the button
5 Day Schedule
You will see one of the 6 period symbols and the symbol
Hold the button until the fi rst period is displayed on
the screen
You can then set the start time for period 1 using the and
buttons
Save your start time by pressing the button, and now
use the and buttons to set the desired temperature and
press the button
Repeat steps for 3 & 4 to set all 6 periods
Weekend Schedule
After completing the 5 day schedule, press the button
for weekend heating
The time you select will apply for both Sat and Sun
Save your start time by pressing the button, and use
the and buttons to set the desired temperature
Press the button to advance to period 2
Set the desired start time and temperature
Finally, press the button to save your 7 day
heating schedule
Amber-Touch
Complete Guide
Up
Button
Down
Button
Menu
Button
Clock
Button
Power
Button
Sensor
Before programming your Amber-Touch
please ensure you read through all these
settings carefully.
Manual Control
If required you may choose to access manual
control of your Amber-Touch. You can easily
switch between the manual mode and your
custom schedule by tapping the button
When in manual mode, you will see the
manual control mode icon , and can
manually set a desired temperature for your
room by using the and buttons.
The symbol will appear when the desired
temperature is set above the ambient room
temperature.
Frost Protection
An active frost protection feature will ensure
your substrate never falls below 10°C. Helping
to reduce the heat up times and protecting the
fl oor fi nish from potential damage.
Having initiated the advanced settings, tap
the button continuously until you see
the frost protection mode (5LrP)
Using the and buttons, simply set
this to ‘ON’ to activate.
Use the button to switch off and save
your settings.
Maximum Floor Temperature
Having initiated the advanced settings, tap
the button continuously until you see the
maximum fl oor temperature mode (3Lit).
Use and buttons to set required
temperature
Press the button to save
1
2
3
5
4
1
2
3
5
4
6
Sensor Mode
Having initiated the advanced settings, tap the
button to switch to Sensor Mode (2SEN) and
set to OUT by using the and buttons
There are 3 sensor modes available to choose
from, Air Sensor Only (IN), Floor Sensor Only (OUT)
and Air Sensor with Floor Limit (ALL), you can
scroll through these using the and buttons.
Use the button to switch off and save your
settings.
We would recommend Floor Sensor Only (OUT) for wetrooms
where the thermostat is located outside the heated area or
where the heating is only required for fl oor warming.
Air Sensor with Floor Limit (ALL) is used where the thermostat is
located within the heated room and the underfl oor heating is the
primary heat source.
DO NOT use Air Sensor Only (IN) with underfl oor heating.
Time & Date Setup
With the unit on, simply hold the button
until the minutes begin to fl ash (5 seconds)
Set the correct time by using the and
buttons, using the button to switch from
minutes to hours and again to edit the day
Use the and buttons to select the
correct day: 1 = Monday, 7 = Sunday
Tap the button to complete the process
Initiate Advanced Settings
Advanced settings must be confi gured before
programming, to initiate:
Switch off the unit by tapping the button
Simultaneously hold the and buttons
until 1ADJ shows on the screen
1
2
Air Sensor
(IN)
Floor Sensor
(OUT)
Air Sensor with
Floor Limit (ALL)
1
2
3
4
5
6
7
Up
Down
Power
Manual Control
Mode
Programme
Mode Indicator
Menu
Heating On
Clock
Period 1
Period 2
Period 3
Period 4
Period 5
Period 6
Screen
Lock
For technical information contact:
0800 056 0494
