Amber Wireless BlueNiceCom 4 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 16

Amber Wireless BlueNiceCom 4 Скачать руководство пользователя страница 15

AMB2300 manual V2.3

15/16

Released: 28.01.2010

7.3 Bluetooth SIG Qualification Design Certificate QDID B013784

Figure 9

SIG QDL Certificate

7.4 Compliance statement

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.

IC compliance statement

Operation is subject to the following two conditions:

1) this device may not cause interference, and

2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.

«
...
13
14
15
16
»

Содержание BlueNiceCom 4

















Отзывы:

Нет отзывов