background image

 

 

 

 © Copyright 2015 Amano McGann, Inc.                                        

OPUS2000_USOperations_03052015

 

 

23 

OPUS-2000 Operations Manual 

 

6.1.3 In-Operation Time 

 

The in-operation time determines the time period the Entry Terminal can be 

used. Enter the 

In-Operation Time Setting 

menu by pressing 

3

. To activate the 

Start/End Time Setting 

press 

1

. The current status of the setting is shown near 

the top of the display. 

 

 

[Fig. 6.1D] Option is disabled 

 

Edit the 

Start Time 

by pressing 

on the remote and entering the desired OPEN 

time in a 24-hour format. Once the desired 

Start Time 

is set, press 

Chan Down 

to accept the change. Edit the 

End Time 

by pressing 

and entering the desired 

CLOSE time in a 24-hour format. Once the desired 

End Time 

is set, press 

Chan 

Down 

to accept the change. 

 

6.1.4 Backlight Time Activation 

 

The OPUS-2000 backlight may be activated at a user-specified 

Start 

and 

End 

time. To navigate to the 

Backlight Setting 

menu, open the 

Management 

Operation 

menu and press 

4

. To activate the 

Backlight ON/OFF Time setting 

press 

1

. The current status of the setting is shown near the top of the display. 

 

 

[Fig. 6.1E] Option is enabled 

 

Edit the 

Start Time 

by pressing 

on the remote and entering the desired ON time 

in a 24-hour format. Once the desired 

Start Time 

is set, press 

Chan Down 

to 

accept the change. Edit the 

End Time 

by pressing 

and entering the desired 

OFF time in a 24-hour format. Once the desired 

End Time 

is set, press 

Chan 

Down 

to accept the change. 

 

6.1.5 Volume Switch 

 

The volume switch time determines the time the Entry Terminal will use volume 

one rather than volume two. This feature is often used when ambient noise is 

louder at a certain point of time in the day. To add a volume switch time, press 

5

 

from the 

Management Operation 

menu. 

 

Activate the volume switch by pressing 

1

. The current status is shown near the 

top of the menu. Edit the start time by pressing 

and entering the desired value 

in a 24-hour format. Press 

Chan Down 

to confirm the entry. Press 

and enter 

the 

End Time 

in a 24-hour format. Press 

Chan Down 

to confirm the entry. 

 

 

 

Содержание OPUS-2000 Series




























Отзывы: