Amana W10233410A Скачать руководство пользователя страница 24

24

DRYER CARE

Cleaning the Dryer Location

Keep dryer area clear and free from items that would obstruct the 
flow of combustion and ventilation air.

Cleaning the Lint Screen

Every loa

d

 cleaning

The lint screen is located in the door opening of the dryer. The 
control panel has an indicator light to remind you to clean the lint 
screen before each load. A screen blocked by lint can increase 
drying time.

To clean

1.

Pull the lint screen straight up. Roll lint off the screen with 
your fingers. Do not rinse or wash screen to remove lint. 

 

Wet lint is hard to remove.

2.

Push the lint screen firmly back into place.

IMPORTANT:

Do not run the dryer with the lint screen loose, damaged, 
blocked, or missing. Doing so can cause overheating and 
damage to both the dryer and fabrics.

Some towels made of synthetic fibers and natural fibers 
(polyester and cotton blends) may shed more lint than other 
towels, causing your dryer’s lint screen to fill up faster. Be 
sure to remove lint from the lint screen before and after drying 
new towels.

If lint falls off the screen into the dryer during removal, check 
the exhaust hood and remove the lint. See “Venting 
Requirements.”

As nee

d

e

d

 cleaning

Laundry detergent and fabric softener residue can build up on the 
lint screen. This buildup can cause longer drying times for your 
clothes, or cause the dryer to stop before your load is completely 
dry. The screen is probably clogged if lint falls off while the screen 
is in the dryer. 

Clean the lint screen with a nylon brush every 6 months, or more 
frequently, if it becomes clogged due to a residue buildup.

To wash

1.

Roll lint off the screen with your fingers.

2.

Wet both sides of lint screen with hot water.

3.

Wet a nylon brush with hot water and liquid detergent. Scrub 
lint screen with the brush to remove residue buildup.

4.

Rinse screen with hot water.

5.

Thoroughly dry lint screen with a clean towel. Replace screen 
in dryer.

Cleaning the Dryer Interior

To clean 

d

ryer 

d

rum

1.

Make a paste with powdered laundry detergent and very 
warm water.

2.

Apply paste to a soft cloth.

OR

Apply a liquid, nonflammable household cleaner to the 
stained area and rub with a soft cloth until all excess dye and 
stains are removed.

3.

Wipe drum thoroughly with a damp cloth.

4.

Tumble a load of clean cloths or towels to dry drum.

NOTE: 

G

arments that contain unstable dyes, such as denim blue 

jeans or brightly colored cotton items, may discolor the dryer 
interior. These stains are not harmful to your dryer and will not 
stain future loads of clothes. Dry unstable dye items inside out to 
avoid transfer of dye.

Removing Accumulated Lint 

From Insi

d

e the Dryer Ca

b

inet

Lint should be removed every 2 years, or more often, depending 
on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending 
on dryer usage.

Содержание W10233410A





























Отзывы: