manualshive.com logo in svg

Amana RS4100004, Сервисная инструкция

Поделиться
Скачать
Amana RS4100004 Скачать руководство пользователя страница 36

RS4100004 Rev. 0

36

Vent Control Assembly Removal

To remove vent control assembly:

1. Remove outer case (see paragraph 

Outer Case

Removal).

2. Remove two ¼-inch screws securing top cover to

chassis, then pull top cover up and away.

3. Remove ¼-inch screw securing vent door to partition

panel.

4. Remove Phillips head screw securing vent door slide

to control panel.

5. Lift vent control assembly out and away from chassis.

Vent Control Removal

Disassembly Procedures

!

WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect electrical power source to unit and
discharge capacitor through a 10,000 ohm resistor before attempting to service, unless test procedures require
power to be connected. Ensure all ground wires are connected before certifying unit as repaired and/or
operational.

Electronic Control Removal

To remove electronic control:

1. Remove outer case (see paragraph 

Outer Case

Removal).

2. Discharge capacitor through 10,000 ohm resistor.

3 Disconnect connector plug between control and

wiring harness.

4. Remove four Phillips head screws securing electronic

control to control panel.

5. Remove thermostat sensor from thermostat sensor

mounting clip on front of evaporator.

6. Carefully work electronic control and attached

thermostat sensor out and away from control panel.

Electronic Control Removal

Control
panel

Electronic
control

Vent
door
slide

Vent door

Top cover

Содержание RS4100004










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды