background image

Amana

Fayetteville, TN 37334

!

RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.

ATTENTION INSTALLING PERSONNEL

As a professional installer you have an obligation to
know the product better than the customer.  This
includes all safety precautions and related items.

Prior to actual installation, thoroughly familiarize
yourself with this Instruction Manual. Pay special
attention to all safety warnings. Often during installation
or repair it is possible to place yourself in a position
which is more hazardous than when the unit is in
operation.

Remember, it is your responsibility to install the product
safely and to know it well enough to be able to instruct
a customer in its safe use.

Safety is a matter of common sense...a matter of
thinking before acting. Most dealers have a list of
specific good safety practices...follow them.

The precautions listed in this Installation Manual should
not supersede existing practices but should be
considered as supplemental information.

®

Table of Contents

ATTENTION INSTALLING PERSONNEL ..................... 1
Safety Guidelines ......................................................... 2
General ........................................................................... 2

SHIPPING AND HANDLING ..................................................... 2
LOCATION AND CLEARANCES .............................................

2

ROOFTOP INSTALLATION .....................................................

2

APPLICATION NOTE ...............................................................

2

Refrigerant Piping ......................................................... 3

REFRIGERANT LINE SIZING .................................................

3

ROUTING REFRIGERANT LINES ..........................................

3

FILTER DRIER INSTALLATION ...............................................

3

SWEAT CONNECTIONS .........................................................

3

Safe Refrigerant Handling ........................................... 3

LEAK TESTING ........................................................................

4

SYSTEM EVACUATION ...........................................................

4

Electrical Connections ................................................. 5
System Startup ............................................................. 6

PRELIMINARY CHARGE ADJUSTMENT ...............................

6

FINAL CHARGE ADJUSTMENT .............................................

6

TROUBLESHOOTING .............................................................

7

Defrost System ............................................................. 7

GENERAL ................................................................................

7

TIME AND TEMPERATURE DEFROST CONTROL ...............

7

DEMAND DEFROST CONTROL .............................................

8

System Checklist .......................................................... 9
Thermostat Connections ........................................... 10

June 1999 (2)

10845803

RHE**A2*

REMOTE HEAT PUMPS

Installation Instructions

Содержание RHE**A2 Series













Отзывы: