11
Programming Menu Items
Oven can program up to 99 separate menu items.
Quantities from one to nine for each menu item may be
programmed. Each item may be programmed for up to 4
independent cooking stages. The 99 programmed items
may be distributed or organized into groups by assigning
them to any of the 4 available menus. Follow instructions
below to program new menu items.
1.
Open oven door.
• Display shows "door". If door is closed or
RESET
is pressed before finishing programming sequence,
oven exits programming mode.
2.
Press and hold pad number
1 for five seconds.
• After five seconds, signal sounds. “P” and active
menu display.
3.
Press
ADD to begin programming.
4.
Press desired menu pad to be preprogrammed, if not
displaying.
• "MENU" indicator displays.
5.
Press two number pads representing menu item.
• "QTY" (quantity) and "LIMIT" indicators and the
current quantity limit flash.
6.
Press number pad to enter quantity.
• Quantity selected, program time and power level for
stage 1 display. "STG" (stage) indicator and stage
numbers with nonzero times also light up if multiple
stages exist.
• If quantity selected is not within quantity limit,
signal sounds. Repeat step 6.
7.
Press numbers to enter desired cooking time.
• Change power level by following procedures 8-9
If 100 percent power is desired, proceed to step 10.
8.
Press
POWER LEVEL.
• "COOK LEVEL" indicator and current power level
display.
9.
Press numbers to enter desired power level. New
power level displays. .
• For example, press pad number
2 for 20 percent
power.
10. Press
START pad to lock new heating time and
power level in oven memory.
• Display shows "P". Repeat steps 5-10 for addi-
tional programming.
11. Press
RESET pad or close oven door to exit
programming mode.
To change quantity limit:
• Press hidden enable pad. Locate hidden enable pad
to the immediate left and slightly down from the
MENU 1 pad. Signal sounds.
• Press number pad to enter quantity limit. Maximum
quantity limit for each menu item is nine.
• Press
START to save new quantity limit.
Programming Multiple Heating Stages
Follow instructions below to program oven to perform 4
consecutive heating cycles without interruption.
1.
Complete steps 1-9 of "Programming Menu Items".
2.
Press
STATUS pad to move through stages from
lowest to highest (1 to 4).
• Display shows "PX" for one second followed by
time and power level for selected stage. "P" repre-
sents program, "X" represents stage 1,2,3 or 4.
3.
Press number pads to enter desired cooking time
and power level.
4.
Repeat steps 2-3 for additional stages.
5.
Complete steps 10-11 of "Programming Menu Items".
Programming Pause
Pause is used to stop microwave power halfway through
cooking cycle as a reminder to manipulate food. To
program pause:
• Press PAUSE pad after entering cooking time.
• Oven stops, displays "PAUS" and signals three times
halfway through cooking cycle. "PAUS" remains in
display until door is opened or STOP/RESET pad is
pressed.
• To resume microwave power, close oven door and press
START pad. Pause can be programmed into menu
items, and can also be programmed when using time
entry.
Deleting Items
To remove items from programming:
1.
Open oven door.
• Display shows "door". If door is closed or
RESET
pad is pressed before finishing programming
sequence, oven exits programming mode.
2.
Press pad
1 for five seconds.
• After 5 seconds, signal sounds. Display shows “P”
and active menu.
3.
Press desired item to be deleted.
4.
Press
DELETE pad twice.
• All cooking stages and power levels for all quanti-
ties of this item are set to zero. Display shows "P".
5.
Press
RESET pad or close oven door to exit
programming mode.
