background image

12

Using the Controls

The temperature controls are located at the top front of the 
refrigerator or freezer compartments. 

Temperature Controls

For your convenience, the temperature controls are preset at the 
factory. When you first install your refrigerator, make sure the 
controls are still set to the recommended setting as shown.

Recommended Setting “4”

IMPORTANT: 

The recommended setting should be correct for normal 
household refrigerator use. The controls are set correctly 
when milk or juice is as cold as you like and when ice cream is 
firm.

Wait 24 hours for your refrigerator to cool completely before 
adding food. If you add food before the refrigerator has cooled 
completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature 
controls to a colder than recommended setting will not cool 
the compartments any faster.

If the temperature is too warm or too cold in the refrigerator or 
freezer, first check the air vents to be sure they are not 
blocked before adjusting the controls. 

To Turn Off/On:

Press the freezer down arrow touch pad until a dash (-) 
appears in both the refrigerator and freezer displays. Neither 
compartment will cool when cooling is off. 

Humidity Control (on some models)

The humidity control turns on a heater to help reduce moisture on 
the door hinge seal. Use in humid environments or when you 
notice moisture on the door hinge seal. The refrigerator uses more 
energy when Humidity Control is on.

Press the control to ON when the environment is warm and 
more humid, or if you notice moisture on the door hinge seal. 

Press the control to OFF to save energy when the environment 
is less humid. 

Adjusting Controls

If you need to adjust the temperature in either the refrigerator or 
freezer compartment, use the settings listed in the chart below as 
a guide. 

Press the up or down arrow touch pads to adjust the 
temperature. Except when starting the refrigerator, do not 
adjust either control more than one setting at a time. Wait 
24 hours between adjustments for the temperature to 
stabilize. 

Crisper Humidity Control 

You can control the amount of humidity in the moisture-sealed 
crisper. Depending on your model, adjust the control to any 
setting between FRUIT and VEGETABLES or LOW and HIGH.
FRUIT/LOW (open) for best storage of fruits and vegetables with 
skins. 
VEGETABLES/HIGH (closed) for best storage of fresh, leafy 
vegetables. 

Ice Maker 

(on some models)

IMPORTANT: Flush the water system before turning on the ice 
maker. See “Water Dispenser.” 

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the 
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made, 
the ice cubes will fill the ice storage bin and the ice cubes will 
raise the wire shutoff arm to the OFF (arm up) position. Do not 
force the wire shutoff arm up or down.

NOTE: Turn off the ice maker before removing the ice storage bin 
to serve ice or to clean the bin. This will keep the ice cubes from 
dropping out of the ice maker and into the freezer compartment. 
After replacing the ice storage bin, turn on the ice maker. 

CONDITION/REASON:

ADJUSTMENT:

REFRIGERATOR too warm

REFRIGERATOR Control 
one setting higher 

FREEZER too warm/too little ice

FREEZER Control one 
setting higher

REFRIGERATOR too cold

REFRIGERATOR Control 
one setting lower

FREEZER too cold

FREEZER Control one 
setting lower

Содержание ABB1921WEW2





















Отзывы: