Altuscn KM0032 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 155

Altuscn KM0032 Скачать руководство пользователя страница 19

Chapter 1. Introduction

7

4

LAN LED

The LED lights ORANGE to indicate 10 Mbps data
transmission speed.

The LED lights GREEN to indicate 100 Mbps data
transmission speed.

The LED flashes when data is being transmitted

5

Reset Switch

Pressing in this button performs a system reset. When the
system is reset, the switch beeps, and then the KVM port
LEDs flash in succession until the reset is completed. After
the reset is completed you can login again.

Note

: This switch is recessed and must be pushed with a

thin object.

6

Cover Latch

7

Firmware
Upgrade
Recovery Switch

During normal operation and while performing a firmware
upgrade, this switch should be in the NORMAL position. If a
firmware upgrade operation does not complete successfully,
this switch is used to perform a firmware upgrade recovery
(see

Firmware Upgrade Recovery

, page 104, for details).

8

Console (User)
Port

This console port is provided on the front panel for easy
administrative access

No.

Component

Description

«
...
17
18
19
20
21
...
»

Содержание KM0032




























































































































































Отзывы:

Нет отзывов