Altuscn KM0032 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 155

Altuscn KM0032 Скачать руководство пользователя страница 116

KM0032 / KM0532 / KM0932 User Manual

104

8. Click

Upgrade

to start the upgrade procedure. As the upgrade proceeds,

progress information is shown on the screen. Once the upgrade completes
successfully, the switch resets itself.

9. Log in again, and check the firmware version to be sure it is the new one.

Firmware Upgrade Recovery

Should the switch’s firmware upgrade procedure fail, and the switch becomes
unusable, the following firmware upgrade recovery procedure will resolve the
problem:

1. Power off the switch.

2. Press and hold the Reset Switch in (see

, page 7 for details).

3. While holding the Reset Switch in, power the switch back on.

This causes the switch to use the original factory installed main firmware
version. Once the switch is operational, you can try upgrading the main
firmware again.

Adapter Cable Firmware Upgrade Recovery

Should the adapter firmware upgrade procedure fail for one of the KVM
Adapter Cables and the adapter becomes unusable, the following adapter
firmware upgrade recovery procedure will resolve the problem:

1. Unplug the Adapter from the computer it is connected to.

2. Slide its

Firmware Upgrade Recovery Switch

(located next to the Cat 5e/

Cat 6 cable connector) to the

RECOVER

position.

3. Plug the Adapter back into the computer.

4. Repeat the Adapter upgrade procedure.

5. After the Adapter has been successfully upgraded, unplug the Adapter

from the computer it is connected to; slide the Firmware Upgrade
Recovery Switch back to the

NORMAL

position; and plug the Adapter

back in.

«
...
114
115
116
117
118
...
»

Содержание KM0032




























































































































































Отзывы:

Нет отзывов