Altronix TROVE T3MK75F16V, Руководство по установке

Страница: 2 / 8

- 2 - T3MKV Kits
Overview:
Altronix Trove Mercury kits are pre-assembled and consist of Trove3M3 enclosure/backplane with factory installed Altronix power
supply/charger(s) and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to sixteen (16) doors
in a single enclosure.
Configuration Chart:
Altronix
Model Number 220VAC 50/60Hz Input Current (A) Power Supply Board Input Fuse Rating Power Supply Board Battery Fuse Rating
Nominal DC Output Voltage
Maximum
Supply
Current for
Main and Aux.
Outputs on Power
Supply board
and ACM8(CB)
Access Power
Controller’s
outputs Fail-Safe/Fail-Secure or Dry Form “C” Outputs Current Per ACM8(CB) Output
(A)
ACM8(CB) Board Input Fuse Rating ACM8 Board Output Fuse Rating ACM8CB Board Output PTC Rating PD8UL Board Output Fuse Rating PD8ULCB Board Output Fuse Rating
Power Supply 1 Power Supply 2
[DC] [Aux] [DC] [Aux]
Output Range (VDC) Output Range (VDC) Output Range (VDC) Output Range (VDC)
T3MK75F16V 4.8
6.3A/250V
5A/250V
15A/
32V
20.17-
26.4
20.28-
26.4
9.7-
13.2
10.03-
13.2
12VDC @ 9.3A
24VDC @ 9.2A
16 2.5
10A/
250V
2.5A/
250V
–
3.5A/
250V
–
T3MK75F16DV
4.8
6.3A/250V
5A/250V
15A/
32V
20.17-
26.4
20.28-
26.4
9.7-
13.2
10.03-
13.2
12VDC @ 9.3A
24VDC @ 9.2A
16 2.5
10A/
250V
– 2A – 2.5A
T3MK77F16V 5.4
6.3A/
250V 15A/
32V
20.17-
26.4
20.28-
26.4
20.17-
26.4
20.28-
26.4
24VDC @ 9.2A 16 2.5
10A/
250V
2.5A/
250V
–
3.5A/
250V
–
T3MK77F16DV
5.4
6.3A/
250V 15A/
32V
20.17-
26.4
20.28-
26.4
20.17-
26.4
20.28-
26.4
24VDC @ 9.2A 16 2.5
10A/
250V
– 2A – 2.5A
Hardware and Accessories:
• Two (2) tamper switches (Altronix Model TS112 or equivalent).
• Cam lock.
• Battery leads.
Mechanical:
• 16 Gauge enclosure with ample knockouts for convenient access.
• Enclosure Dimensions (H x W x D): 36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm).
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install
the three fasteners. Place the enclosure’s upper keyholes over the three upper screws.
Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switches (Altronix Model TS112 or equivalent) in desired location,
opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2”
from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input
or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.
4. Mount Mercury boards to backplane, refer to pg. 3, 4.
5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow104NBV, eFlow102NBV
and corresponding Sub-Assembly Installation Guides for PD8UL(CB) and ACM8(CB) for
further installation instructions.
6. Position Mercury access controller module over corresponding spacers and depress onto
snap on spacers (Fig. 2-3, pg. 3-4).
7. Mount backplane to enclosure with hardware.
Fig. 1
Tamper Switch
(provided)
To Access Control Panel or
UL Listed Reporting Device
Edge of
Enclosure
Enclosure