Overview:
These Altronix Rack Mount CCTV Power Supplies provide 24VAC or 28VAC distributed via sixteen (16) fuse or
PTC protected outputs for powering CCTV Cameras, heaters and other video accessories.
Sixteen (16) Output Rack Mount Configuration Reference Chart:
Altronix
Model Number
Output Voltage (VAC)
Total Output Current (Power)
Number of Outputs
PTC Protected Outputs (Class 2 power limited for
Dry locations).
(Class 3 for Wet locations).
Fuse Protected Class 1 Outputs
Individual Output Current (max per output not to exceed total output current)
Fuse Ratings
Primary In-line Fuse Ratings
115VAC 50/60Hz Input Current
Agency Listings
R2416UL
24VAC
7 amp
16
Yes 3.5 amp
3.5
amp
3.5 amp/
250V
2.9 amp
28VAC
6 amp
R2416ULCB
24VAC
7 amp
16
Yes
2.5 amp
3.5 amp/
250V
2.9 amp
28VAC
6 amp
R2416300UL
24VAC 12.5 amp
16
Yes 3.5 amp
3.5
amp
3 amp
28VAC
10 amp
R2416300ULCB
24VAC 12.5 amp
16
Yes
2.5 amp
3 amp
28VAC
10 amp
R2416600UL*
24VAC
25 amp
16
Yes 3.5 amp
3.5
amp
6 amp
28VAC
20 amp
R2416600ULCB
24VAC
25 amp
16
Yes
2.5 amp
6 amp
28VAC
20 amp
*24VAC models: Outputs 1-8 provide 12.5 amp (300VA) max. Outputs 9-16 provide 12.5 amp (300VA) max.
*28VAC models: Outputs 1-8 provide 10 amp (280VA) max. Outputs 9-16 provide 10 amp (280VA) max.
Specifications:
•
UL
Listed
for
Commercial
CCTV
Equipment
(UL
2044).
•
Sixteen
(16)
individual
power
LED
indicators.
CUL
Listed
- CSA
Standard
C22.2
No.
1-98,
Audio,
•
Removable
terminal
blocks
with
locking
screw
flange.
Video
and
Similar
Equipment.
•
Unit
maintains
camera
synchronization.
•
24VAC
or
28VAC
(Factory
set
@
24VAC).
•
Ease
of
installation
saves
time
and
eliminates
costly
labor.
•
Illuminated
power
disconnect
circuit
breaker
•
2U
rack
mount
chassis
for
use
in
standard
EIA
19”
rack.
with manual reset
Rack Dimensions:
•
Surge
suppression.
3.25”H x 19.125”W x 8.5”D
Installation Instructions:
1. Mount unit in desired rack location (Space unit at least 3” from any video monitors), Do not obstruct side air vents.
2. Set power disconnect circuit breaker to OFF position (Fig. 1d, pg. 3).
3. The unit is factory set for 24VAC operation.
For 28VAC operation, adjust unit prior to mounting and applying power as follows:
a. Open bottom of unit by removing six (6) screws (Rack Mechanical Drawing & Dimensions, pg. 4).
b. For 28VAC operation, adjust unit prior to mounting and applying power as follows:
Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and
the yellow wire [24V] is connected to the terminal marked [S].
c. After securing all wires for proper voltage place bottom panel back on the unit and fasten with the six (6) screws.
Note: R2416ULCB set for 28VAC operation is not Class 2 Rated, not power limited.
4. Plug power cord into grounded 115VAC 50/60 Hz receptacle (Fig. 1c, pg. 3), ground should be connected
as indicated in (Fig. 1e, pg. 3).
- 2 -
R2416ULseries
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
