Altronix HubSat42WPiV, Руководство по установке

Страница: 2 / 12

- 2 - HubSat4WPiV
Overview:
Altronix HubSat4WPiV Passive UTP Transceiver Hub with Integral Isolated Camera Power transmits UTP video, RS422/
RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels in a wall mount
enclosure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or
PTZ cameras when utilizing Altronix HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners. In addition, the
unit features individually selectable 24VAC or 28VAC PTC protected outputs with surge suppression. Optionally, the
HubSat4WPiV can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher
structured cables back to the HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addi-
tion, the HubSat4WPiV provides power to these cameras locally to eliminate the possibility of voltage drop associated with
long cable runs.
Input:
• 220VAC, 50/60Hz, 0.7A.
Video:
• Four (4) channels of quality video over twisted pair
up to a distance of 750 ft. per channel.
• Four (4) 75 Ohm video outputs.
Data:
• RS422/RS485 data input.
Power:
• Individually selectable 24VAC or 28VAC isolated power
outputs with OFF position.
• Unit provides up to 1A max. per channel not to
exceed a total of 4A maximum current.
Power (cont’d) :
• PTC protected outputs are rated @ 1A per channel.
• Surge suppression.
Visual Indicators:
• Four (4) power LED indicators.
Enclosure Dimensions (H x W x D approx.) :
12” x 8” x 6” (304.8mm x 203.2mm x 152.4mm)
Optional Accessories:
• Video Balun/Combiners:
- HubWayAv - for use with 24VAC cameras.
- HubWayAv2 - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
Specifica tions:
HubSat42WPiV
• HubSat4WPiV with four (4) HubWayAv
Video Balun/Combiners for 24VAC Cameras.
HubSat43WPiV
• HubSat4WPiV with four (4) HubWayDv
Video Balun/Combiners for 12VDC Cameras.
WARNING: This installation should be made by qualified service personnel. Unit should be installed in
accordance with the National Electrical Codes and all local codes. For continued protection against risk of
fire replace all fuses only with the same type and rating.
Installation Instructions:
HubSat4WPiV Outdoor Passive UTP Transceiver Hub with Integral Isolated Camera Power.
1. Remove back plate inside the enclosure by removing the four (4) mounting screws (Fig. 5, pg. 6).
2. Mark and drill desired knockouts on the enclosure to facilitate wiring (Fig. 1, pg. 4).
3. Secure back plate inside the enclosure with the four (4) mounting screws (Fig. 5b, pg. 6).
4. Unit can be wall or pole mounted.
Wall Mount:
- Mark and drill holes to line up with the top and bottom holes of the enclosure flange.
- Secure enclosure with appropriate fasteners (Enclosure Dimensions, pg. 12).
Pole Mount:
- Refer to the detailed pole mount instructions (pg. 9).
Secure enclosure to earth ground.
5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5a, pg. 6).
6. Connect 220VAC 50/60Hz to the black and red flying leads of open frame transformer. Secure ground
wire (Green) to earth ground (Fig. 5, pg. 6).
7. S elect 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat4WPiV (Fig. 5, pg. 6) with the
corresponding output voltage switches. Select OFF position when servicing or installing individual
cameras (Fig. 2d, pg. 4).
8. Connect the BNC video outputs marked [Video 1-4] on HubSat4WPiV to the corresponding video inputs on the
head end equipment (DVR) (Fig. 2a, pg. 4).
9. Connect terminals marked [+ Data --- ] on HubSat4WPiV (polarity must be observed) to the RS422/RS485 output
of the head end equipment (DVR) (Fig. 2f, pg. 4). When using fixed cameras disregard this step.
10. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]
on HubSat4WPiV (Fig. 2i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured
cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.
Additional Models: