background image

 AL175UL 

- 3 -

Terminal Identification:

Terminal Legend Function/Description

42'42'

Connects to the normally closed outputs of an access control or fire alarm relay. These terminals 

CONTROL;,/#+=AND;342)+%=ASWELLAS!,5,OUTPUTRELAYCONTACTS;.#./#=

.

,/#+

0ROVIDES$#OUTPUTVOLTAGEWHEN;42'=AND;42'=ARESHORTEDTOGETHERANDARETYPICALLY

used to power Mag Locks.

342)+%

0ROVIDES$#OUTPUTVOLTAGEWHEN;42'=AND;42'=AREUNSHORTEDANDARETYPICALLYUSEDTO
POWER%LECTRIC3TRIKES

.#./#

)SOLATEDDRYFORMh#vCONTACTS3HORTING;42'=AND;42'=TOGETHERCAUSESTHESECONTACTSTO

switch. They are typically used for controlling multiple AL175ULs with fire alarm tie-in 

(Fig. 5 and Fig. 6, pg. 4)

.

AUX +

#ONTINUOUSPOSITIVE $#POWEROUTPUTVOLTAGE)TISNOTAFFECTEDBY42'42'OPERATION

#/-

Common negative (-) output (ground). 

FACP

3PAREWIRINGTERMINALUSEDFORFIREALARMTIEINAPPLICATION

(Fig. 4, pg. 4).

"!4

3TANDBYBATTERYCONNECTIONS

AC FAIL 

.##./

Indicates loss of AC, e.g connect audible device or alarm panel. Relay normally energized

WHEN!#POWERISPRESENT#ONTACTRATINGAMP 6$#

Enclosure Dimensions 

(H x W x D approximate)

:

vXvXvMMXMMXMM 

1.25”

(31.75mm)

1.25”

(31.75mm)

1.25”

(31.75mm)

1.125”

(28.575mm)

1”

(25.4mm)

1”

(25.4mm)

1”

(25.4mm)

5.25”

(133.35mm)

6.05”

(153.67mm)

6.05”

(153.67mm)

3.5”

(88.9mm)

3.5”

(88.9mm)

7.25”

(184.15mm)

2”

(50.8mm)

2”

(50.8mm)

8.125”

(206.375mm)

0.6”

(15.24mm)

1”

(25.4mm)

1”

(25.4mm)

0.6”

(15.24mm)

0.6”

(15.24mm)

1.125”

(28.575mm)

0.6”

(15.24mm)

3.625”

(184.15mm)

Содержание AL175UL

Страница 1: ... BY AMP 6 ATTERY LARM AMP Installation Instructions The AL175UL should be installed in accordance with article 760 of The National Electrical Code or NFPA 72 as well as all applicable Local Codes See Terminal Identification Chart on page 3 for a description of each terminal function 1 Mount the unit in the desired location Mark and predrill holes in the wall to line up with the top two keyholes in...

Страница 2: ... LARM ONTROL 0ANEL OR to visual AC trouble indicator 7 For Access Control Device Fire Alarm Interface connections refer to desired Application Diagrams pg 4 and Terminal Identification Chart pg 3 Maintenance 5NIT SHOULD BE TESTED AT LEAST ONCE A YEAR FOR THE PROPER OPERATION AS FOLLOWS Output Voltage Test 5NDER NORMAL LOAD CONDITIONS THE OUTPUT VOLTAGE SHOULD BE CHECKED FOR PROPER VOLTAGE LEVEL se...

Страница 3: ...ple AL175ULs with fire alarm tie in Fig 5 and Fig 6 pg 4 AUX ONTINUOUS POSITIVE POWER OUTPUT VOLTAGE T IS NOT AFFECTED BY 42 42 OPERATION Common negative output ground FACP 3PARE WIRING TERMINAL USED FOR FIRE ALARM TIE IN APPLICATION Fig 4 pg 4 4 3TAND BY BATTERY CONNECTIONS AC FAIL Indicates loss of AC e g connect audible device or alarm panel Relay normally energized WHEN POWER IS PRESENT ONTACT...

Страница 4: ...IN WITH MANUAL RESET Fig 3 Typical dual mag lock installation with fire alarm TIE IN USING TRIGGER CONTROLLED OUTPUTS Fig 6 Multiple AL175UL X power supply CONNECTIONS Fig 2 Typical single mag lock or door strike installation WITH FIRE ALARM TIE IN USING TRIGGER CONTROLLED OUTPUT Typical Application Diagrams Fig 4 Typical mag lock with fire alarm tie in using AUX OUTPUT INSTALLATION LTRONIX IS NOT...

Отзывы: