manualshive.com logo in svg

Alto APM 120, Руководство пользователя

Поделиться
Скачать
Alto APM 120 Скачать руководство пользователя страница 17

15

Ok, you have got to this point and you are now in the position to successfully operate
your APM Series. However, we advise you to read the following section carefully to be
the real master of your own mix. Not paying enough attention to the input signal level,
the routing of the signal and the assignment of the signal will result in unwanted
distortion, a corrupted signal or no sound at all. So you should follow this procedure
for every single channel:

1. Turn down all Input and output gain controls.

2. Connect phantom powered microphones before switching on the +48 Volt phantom

power switch.

3. Set the output level of your APM Series or the connected power amplifier at no more

than 75%.

4. Position EQ controls on middle position.

5. Position panoramic (PAN) control on center position.

6. Increase the input gain properly for maintaining the good headroom and ideal dynamic

range.

7. Depending on the actual application, turn slowly the input and output level controls

for obtaining the maximum gain before distortion.

8. Now repeat the same sequence for all input channels. The main LED meter could

move up into the red section. In this case you can adjust the overall output level
through the main mix control.

You can connect unbalanced equipment to balanced inputs and outputs. Simply follow
these schematics.

Audio Connections

5. INSTALLATION AND CONNECTION

Strain Clamp

Sleeve

Tip

Ring

Sleeve=Ground/Screen

Ring=Right Signal

Tip=Left Signal

Use for Headphone

1/4" Stereo (TRS) Jack Plug

Strain Clamp

Sleeve

Tip

Sleeve=Ground/Screen

Tip=Signal

Use for Mono Line In, Mono 1/4"Jack Plugs

1/4" Mono (TS) Jack Plug

Содержание APM 120




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды