background image

#802/ 1 Operation & Care Manual •

9.

The cleanliness and appearance of this

equipment will contribute

considerably to operating

efficiency and savory,

appetizing food. Good

equipment that is kept

clean works better and lasts

longer.

CLEAN THE CARVING SHELF
AFTER EACH USE:

1.

Disconnect the shelf from the power source.

2.

Remove cutting board after each use. Clean

and sanitize separately following applicable

state or local health sanitation ordinances.

Air dry the board on a clean, flat surface to

prevent board from warping. If the board

becomes warped, heating will restore

flexibility to facilitate flattening. Warped

boards may be heated on the carving shelf

surface, in a preheated Combitherm

combination oven/steamer for 10 minutes on

the steam program, or in a preheated Halo

Heat cook and hold oven for 15 minutes at

250°F (121°C).

3.

Clean metal surface with

mild soap solutions only.

DO NOT clean with lye or

alkaline based cleaners or

any abrasive cleaners.

Rinse carefully with a

clean sponge and water to

remove all soap or

detergent residue.

4.

DO NOT use knives or utensils on the hot

shelf surface. A cutting board is supplied.

5.

Clean the acrylic sneeze guard with soap or

mild detergent and water. Dry with a clean,

damp chamois. Grease and oil may be

removed with naphtha or hexane.

NOTE:

Do not use commercial or household

cleaners containing ammonia on

the sneeze guard. To avoid

scratching, do not use dry cloths or

scouring compounds.

AT NO TIME SHOULD THE INTERIOR 

OR EXTERIOR BE STEAM CLEANED, 

HOSED DOWN, OR FLOODED WITH 

WATER OR LIQUID SOLUTION OF 

ANY KIND. 

DO NOT USE WATER JET TO CLEAN.

 

SEVERE DAMAGE OR ELECTRICAL 

HAZARD COULD RESULT.

 

WARRANTY BECOMES VOID IF

APPLIANCE IS FLOODED.

W A R N I N G

W a r r a n t y d o e s n o t

a p p l y i f t h e c a r v i n g

s h e l f i s f l o o d e d o r

i m m e r s e d i n w a t e r .

C A R E A N D C L E A N I N G

Содержание Hot Carving Shelf 100-HSL/BCS-2




















Отзывы: