background image

DESIGNER SOLUTIONS

400-0109-006

2

PRECAUTIONS / SAFETY WARNINGS

1

Please read this manual carefully before using your 

PNP400

and keep  it handy for future reference. 

These safety instructions are to ensure the long life 
of your 

PNP400

and to prevent fire and shock 

hazards. Please read them carefully and heed all 
warnings.

1.1  GENERAL

There are no user serviceable parts inside. 
Qualified ALTINEX service personnel must 
perform all service on the 

PNP400

.

1.2  HANDLING

For best results, place the 

PNP400

on a flat, 

leveled surface in a dry area away from dust and 
moisture.

To prevent fire or shock, do not expose this unit 
to  water or moisture. Do not place the 

PNP400

in direct sunlight, near heaters, or heat-radiating 
appliances, or near any liquid. Exposure to direct 
sunlight, smoke, or steam can harm internal 
components.

Handle the 

PNP400

carefully. Dropping or 

jarring can damage the unit.

Do not pull any cables that are attached to the 

PNP400.

Do not place heavy objects on top of the 

PNP400

.

Do not use excessive force to push down on the 
top of the unit.

Be careful. Serious injury could result because 
of the sharp edges inside of the 

PNP400

To turn off main power, disconnect the power 
cord powering the 

PNP400

outlets. 

We recommend using wall outlets with a Ground 
Fault Circuit Interrupter (GFCI) for maximum 
protection.

1.3  CLEANING

Unplug the 

PNP400

before cleaning.

Clean only with a dry cloth. Never use strong 
detergents or solvents such as alcohol or 
thinner. Do not use a wet cloth or water to clean 
the unit. Do not open the unit to clean.

1.4  FCC NOTICE

This device complies with Part 15 of the FCC 
Rules. Operation is subject to the following two 
conditions: (1) This device may not cause 
harmful interference, and (2) this device must 
accept any interference received, including 
interference that may cause undesired 
operation.

This equipment has been tested and found to 
comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable 
protection against harmful interference when the 
equipment is operated in a commercial 
environment. This equipment generates, uses, 
and can radiate radio frequency energy and if 
not installed and used in accordance with 
instructions found herein, may cause harmful 
interference to radio communications. Operation 
of this equipment in a residential area is likely to 
cause harmful interference in which case the 
user will be required to correct the interference 
at his own expense.

Any changes or modifications to the unit not 
expressly approved by ALTINEX, Inc. could void 
the user’s authority to operate the equipment.

Содержание Pop 'N Plug Tower PNP400
















Отзывы: