MT312-104
User’s Guide
400-0638-001
9
24. [RDIR*]
Read all IR memory locations programmed with valid IR
codes; incomplete or blank memory locations are not
displayed. Total time to complete is about 5 seconds per
programmed memory location.
Data is returned in command write format. The data can be
saved to a file and used restore IR codes later or to
program other cards that control the same devices.
Command Format:
[RDIR*Cii]
Note: Must send [WRIR0000Cii] when all memory
locations have been read.
Example:
Send [RDIR*C04] to read all programmed IR data strings.
The Neutron responds with 10 blocks in the format
beginning with "[IR" followed by 100 data characters and
concludes with the card ID and close bracket.
[IR21,01, FFFFFFFFFFFFFF00000000000FFFF...C04]
[IR21,02, FFFFFFFFFFFFFF00000000000FFFF...C04]
etc.
[IR01,10, FFFFFFFFFFFFFF00000000000FFFF...C04]
25. [OUTIR]
Output the IR data stored in a memory location to one of
the IR outputs to activate the IR emitter and control an
external device.
Command Format:
[OUTIRxmmCii]
x
= IR output number (n= 1 or 2)
mm = IR memory location number (01 to 99, 2-digits)
ii
= Card ID (1-20)
Example:
Output the IR string stored in memory location 2 on IR
output port #1 by sending the following command:
[OUTIR102C04]
This single command reads the entire IR string from
memory and sends it to the IR port. Once the entire
process is complete, the Neutron sends confirmation.
[C04]
26. [WRIRRAM]
Preset the pass-through IR by loading the data into RAM
from the Altinex library directly from the controller. This
command allows virtually unlimited IR commands to be
used in place of, or in addition to, the built-in IR memory of
the Neutron. This command works in conjunction with the
[OUTRAM] command that instructs the controller to output
the data to the IR ports.
Command Format:
[WRIRRAMp,dddCii]
p
= Saving instructions (1=Overwrite, 0=Append)
ddd = IR data in ASCII characters (100 per command),
Valid characters are "0123456789ABCDEF"
Example:
An IR library command string is 1,000 characters and
requires 10 save commands to save the IR string into
RAM. The following command samples are used to load an
IR string into RAM. Remember to wait for command
acknowledgement from the Neutron after sending each
command before sending the next.
[WRIRRAM1,FFFFF...C04]
Overwrite RAM,100 char.
[C04]
Neutron Feedback
[WRIRRAM0,AA00FF...C04]
Append RAM,100 char.
[C04]
Neutron Feedback
[WRIRRAM0,FF00FF...C04]
Append RAM,100 char.
[C04]
Neutron Feedback
etc
.
27. [LEARNIR]
Learn IR data from a remote control using the built-in
IR Learn capability of the MT312-104. Data is captured and
stored directly to one of 99 memory locations.
Command Format: [LEARNIRmmCii]
mm = Memory location (n= 01 to 99, 2-digits)
Before learning IR codes, plan the features required by
your installation. Document the codes to learn and assign
memory locations. Make note of which device will be
connected to which IR output number. See the table below
as an example.
Device
Mfr/Model
Function Memory IR Out
DVD
Panasonic DVD-S54
Power
01
1
DVD
Panasonic DVD-S54
Stop
02
1
DVD
Panasonic DVD-S54
Play
03
1
DVD
Pioneer DVD-V7400
Power
11
2
DVD
Pioneer DVD-V7400
Stop
12
2
DVD
Pioneer DVD-V7400
Play
13
2
TV
Sony Bravia
Power
21
3
