background image

MULTITASKER

400-0394-007

2

PRECAUTIONS / SAFETY WARNINGS

1

Please read this manual carefully before using your 

MT106-103

. Keep this manual handy for future 

reference. These safety instructions are to ensure 
the long life of your 

MT106-103

and to prevent fire 

and shock hazards. Please read them carefully and 
heed all warnings.

1.1 GENERAL

Qualified ALTINEX service personnel or their 
authorized representatives must perform all 
service.

1.2 INSTALLATION

To prevent fire or shock, do not expose this unit 
to water or moisture. Do not place the 

MT106-103 

in direct sunlight, near heaters or 

heat-radiating appliances, or near any liquid. 
Exposure to direct sunlight, smoke, or steam can 
harm internal components.

Handle the 

MT106-103 

carefully. Dropping or 

jarring can damage the card.

Do not pull any cables that are attached to the

MT106-103

.

Insert the card carefully into the slots of the 
MultiTasker without bending any edges.

1.3 CLEANING

Clean only the connector area with a dry cloth. 
Never use strong detergents or solvents, such 
as alcohol or thinner. Do not use a wet cloth or 
water to clean the card. Do not clean or touch 
any component or PCB.

1.4 FCC NOTICE

This device complies with Part 15 of the FCC 
Rules. Operation is subject to the following two 
conditions: (1) This device may not cause 
harmful interference, and (2) this device must 
accept any interference received, including 
interference that may cause undesired 
operation.

This equipment has been tested and found to 
comply with the limits for a Class A digital device 
pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable 
protection against harmful interference when the 
equipment is operated in a commercial 
environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if 
not installed and used in accordance with the 
instruction manual, may cause harmful 
interference to radio communications. Operation 
of this equipment in a residential area is likely to 
cause harmful interference in which case the 
user will be required to correct the interference 
at his own expense.

Any changes or modifications to the unit not 
expressly approved by ALTINEX, Inc. could void 
the user’s authority to operate the equipment.

Содержание MultiTasker MT106-103























Отзывы: