
Chapter 8: Configuration and Remote System Upgrades in Cyclone IV Devices
8–49
Configuration
May 2013
Altera Corporation
You can perform JTAG testing on Cyclone IV devices before, during, and after
configuration. Cyclone IV devices support the
BYPASS
,
IDCODE
, and
SAMPLE
instructions during configuration without interrupting configuration. All other JTAG
instructions can only be issued by first interrupting configuration and
reprogramming I/O pins with the
ACTIVE_DISENGAGE
and
CONFIG_IO
instructions.
The
CONFIG_IO
instruction allows you to configure the I/O buffers through the JTAG
port and interrupts configuration when issued after the
ACTIVE_DISENGAGE
instruction. This instruction allows you to perform board-level testing prior to
configuring the Cyclone IV device or waiting for a configuration device to complete
configuration. Prior to issuing the
CONFIG_IO
instruction, you must issue the
ACTIVE_DISENGAGE
instruction. This is because in Cyclone IV devices, the
CONFIG_IO
instruction does not hold
nSTATUS
low until reconfiguration, so you must disengage
the active configuration mode controller when active configuration is interrupted.
The
ACTIVE_DISENGAGE
instruction places the active configuration mode controllers in
an idle state prior to JTAG programming. Additionally, the
ACTIVE_ENGAGE
instruction
allows you to re-engage a disengaged active configuration mode controller.
1
You must follow a specific flow when executing the
ACTIVE_DISENGAGE
,
CONFIG_IO
,
and
ACTIVE_ENGAGE
JTAG instructions in Cyclone IV devices.
The chip-wide reset (
DEV_CLRn
) and chip-wide output enable (
DEV_OE
) pins in
Cyclone IV devices do not affect JTAG boundary-scan or programming operations.
Toggling these pins do not affect JTAG operations (other than the usual
boundary-scan operation).
When designing a board for JTAG configuration of Cyclone IV devices, consider the
dedicated configuration pins.
describes how you must connect these pins
during JTAG configuration.
Table 8–15. Dedicated Configuration Pin Connections During JTAG Configuration
Signal
Description
nCE
On all Cyclone IV devices in the chain,
nCE
must be driven low by connecting it to GND, pulling it low
through a resistor, or driving it by some control circuitry. For devices that are also in multi-device AS, AP,
PS, or FPP configuration chains, you must connect the
nCE
pins to GND during JTAG configuration or
JTAG configured in the same order as the configuration chain.
nCEO
On all Cyclone IV devices in the chain,
nCEO
is left floating or connected to the
nCE
of the next device.
MSEL
These pins must not be left floating. These pins support whichever non-JTAG configuration that you used
in production. If you only use JTAG configuration, tie these pins to GND.
nCONFIG
Driven high by connecting to the V
CCIO
supply of the bank in which the pin resides and pulling up through
a resistor or driven high by some control circuitry.
nSTATUS
Pull to the V
CCIO
supply of the bank in which the pin resides through a 10-k
resistor. When configuring
multiple devices in the same JTAG chain, each
nSTATUS
pin must be pulled up to the V
CCIO
individually.
CONF_DONE
Pull to the V
CCIO
supply of the bank in which the pin resides through a 10-k
resistor. When configuring
multiple devices in the same JTAG chain, each
CONF_DONE
pin must be pulled up to V
CCIO
supply of the
bank in which the pin resides individually.
CONF_DONE
going high at the end of JTAG configuration
indicates successful configuration.
DCLK
Must not be left floating. Drive low or high, whichever is more convenient on your board.
Содержание Cyclone IV
