manualshive.com logo in svg

Altendorf WA 80, Руководство оператора

Поделиться
Скачать
Altendorf WA 80 Скачать руководство пользователя страница 43

Rip fence with DIGIT X

© ALTENDORF 2007

40

Basic settings of the display elektronics

Fig. 7-14: Display DIGIT X

The basic setting of the display electronics is re-
quired in order to adapt the measuring system tothe
individual machine situation. Check and, if ne-ces-
sary, re-enter the basic setting for each toolchange.
Knowing that the basic setting can only beper-
formed in conjunction with the tools actuallyused,
factory setting is not possible.

–

Push the rip fence to the left against mechani-
cal stop

–

Keep the F Key pressed while pressing RESET

–

Set the rip fence to 130 mm cutting width (flat
position)

–

Cut the trial piece and measure the workpiece
width using a sliding caliper

–

Press and keep the F key pressed, the right-
hand position of the display starts flashing after
3s

–

Use the + key to increase the value of the flas-
hing digit by 1 with each key actuation. When
exceeding the max. number value (9), the num-
bers start again with 0

–

The value of the flashing digit can be decreased
by 1 with each actuation of the - key.

–

Release the 

F

 key

–

The set dimensions is saved as a basic setting
value

Calibration the display elektronics

Calibration of the display electronics is required
when the fence position was change while the ma-
chine was switched off or when the saw blade was
changed.

–

Push the rip fence to the left against the mecha-
nical stop

–

Keep the F key pressed while briefly actuating
the RESET key. The basic setting value reap-
pears in the display

Switch dimension, mm and inch

–

Keep key + pressed for more than 3 s. The dis-
play will show inch (mm)

–

Release key +, the display electronics now
show the set dimension in inch (mm)

Содержание WA 80

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды