Altec ATP-4310 Скачать руководство пользователя

Страница: 84 / 89

- 77 -

SD card is unable to use

* SD card is damaged.
* SD card doesn’t insert

correctly.

* Use the non-approved SD

card manufacturer.

* Use the supported capacity SD card.
* Insert the SD card again.
* The supported SD card spec and the

approved SD card manufacturers,
please refer to section 2.2.3.

Poor Print Quality

* Ribbon and media is loaded

incorrectly

* Dust or adhesive

accumulation on the print
head.

* Print density is not set

properly.

* Printhead element is

damaged.

* Ribbon and media are

incompatible.

* The printhead pressure is not

set properly.

* Reload the supply.
* Clean the print head.
* Clean the platen roller.
* Adjust the print density and print speed.
* Run printer self-test and check the print

head test pattern if there is dot missing in
the pattern.

* Change proper ribbon or proper label

media.

* Adjust the printhead pressure

adjustment knob.

* The release lever does not latch the

printhead properly.

Missing printing on the left or
right side of label

* Wrong label size setup.

* Set the correct label size.

Gray line on the blank label

* The print head is dirty.
* The platen roller is dirty.

* Clean the print head.
* Clean the platen roller.

Irregular printing

* The printer is in Hex Dump

mode.

* The RS-232 setting is

incorrect.

* Turn off and on the printer to skip the

dump mode.

* Re-set the Rs-232 setting.

Label feeding is not stable
(skew) when printing

* The media guide does not

touch the edge of the media.

* If the label is moving to the right side,

please move the label guide to left.

* If the label is moving to the left side,

please move the label guide to right.

Skip labels when printing

* Label size is not specified

properly.

* Sensor sensitivity is not set

properly.

* The media sensor is covered

with dust.

* Check if label size is setup correctly.
* Calibrate the sensor by Auto Gap or

Manual Gap options.

* Clear the GAP/Black mark sensor by

blower.

Wrinkle Problem

* Printhead pressure is

incorrect.

* Ribbon installation is

incorrect.

* Media installation is incorrect.
* Print density is incorrect.
* Media feeding is incorrect.

* Please refer to chapter 4.4.
* Please set the suitable density to have

good print quality.

* Make sure the label guide touch the

edge of the media guide.

RTC time is incorrect when
reboot the printer

* The battery has run down.

* Check if there is a battery on the main

board.

The left side printout position
is incorrect

* Wrong label size setup.
* The parameter Shift X in LCD

menu is incorrect.

* Set the correct label size.
* Press [MENU]



[SELECT] x 3



[DOWN] x 5



[SELECT] to fine tune the

parameter of Shift X.

Содержание ATP-4310


























































































Результаты поиска

Содержание ATP-4310

Отзывы:

Похожие инструкции для ATP-4310

Бренды по названию

Популярные бренды

Altec ATP-4310, Руководство пользователя

Результаты поиска

Содержание ATP-4310

Отзывы:

Похожие инструкции для ATP-4310

Бренды по названию

Популярные бренды