Alpine X-A70F Скачать руководство пользователя страница 3

2

-EN

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR 
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any 
other safety-related system), or tanks should NEVER be 
used for installations or ground connections. Using such 
parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE 
REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed, 
consult a physician immediately.

 CAUTION

This symbol means important instructions.
Failure to heed them can result in injury or 
property damages.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS.

Failure to do so may cause personal injury or damage to 
the product. Return it to your authorized Alpine dealer or 
the nearest Alpine Service Center for repairing.

HAVE THE WIRING AND INSTALLATION DONE BY 
EXPERTS.

The wiring and installation of this unit requires special 
technical skill and experience. To ensure safety, always 
contact the dealer where you purchased this product to 
have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM 
SECURELY.

Be sure to use only the specified accessory parts. Use of 
other than designated parts may damage this unit 
internally or may not securely install the unit in place. This 
may cause parts to become loose resulting in hazards or 
product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR 
PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like 
the seat rails) or sharp or pointed edges. This will prevent 
crimping and damage to the wiring. If wiring passes 
through a hole in metal, use a rubber grommet to prevent 
the wire’s insulation from being cut by the metal edge of 
the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE 
OR DUST.

Avoid installing the unit in locations with high incidence of 
moisture or dust. Moisture or dust that penetrates into this 
unit may result in product failure.

SERVICE CARE

 IMPORTANT NOTICE

This Amplifier has been type tested and found to 
comply with the limits for a Class B computing 
device in accordance with the specifications in 
Subpart J of Part 15 of FCC Rules. This equipment 
generates and uses radio frequency energy, and it 
must be installed and used properly in accordance 
with the manufacturer’s instructions.

SERIAL NUMBER:  
INSTALLATION DATE:  
INSTALLATION TECHNICIAN:  
PLACE OF PURCHASE:  

 IMPORTANT

Please record the serial number of your unit in 
the space provided here and keep it as a 
permanent record. The serial number plate is 
located on the rear of the unit.

  For European Customers

Should you have any questions about warranty, 
please consult your store of purchase.

  For Customers in other Countries

IMPORTANT NOTICE

Customers who purchase the product with which 
this notice is packaged, and who make this 
purchase in countries other than the United States 
of America and Canada, please contact your dealer 
for information regarding warranty coverage.

ACCESSORIES

• 

Self-Tapping Screw (M4 × 20) ......................................4

• 

Terminal Cover (F)/(L)/(R) ......................................1 SET

• 

Battery Connector ...........................................................1

• 

Speaker Connector

X-A90M .............................................................................1
X-A70F ..............................................................................2
X-A90V ..............................................................................3

• 

Hexagon Wrench (Large)/(Small) .......................1 SET

• 

Logo Plate ...........................................................................1

Содержание X-A70F





























Отзывы: