Alpine iLX-507E, Руководство пользователя

Страница: 31 / 80

ALPINE iLX-F509E 68-41657Z84-A (EN) ALPINE iLX-F509E 68-41657Z84-A (EN)
31
-EN
Crossover Settings (X-OVER)
Before performing the following procedures, see “About the
Crossover” (page 32).
Setting item:
X-OVER
1
Touch [X-OVER].
The X-OVER setting screen is displayed.
2
Touch [Front HPF], [Fron
[Rear LPF] or [Subw. LPF] to selec
to adjust.
3
Touch [ ] or [ ] of “Frequency,”
select the cut-off frequency.
Setting contents:
Front HPF:
Front LPF: 4k / 5k / 6.3k / 8k (I
12.5k / 16k / 20k Hz
Rear HPF:
Rear LPF: 4k / 5k / 6.3k / 8k (I
12.5k / 16k / 20k Hz
Sub.w.LPF:
4
Touch [ ] or [ ] of “Slope,”
the HPF or LPF slope.
Setting contents:
0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
5
Touch [ ] or [ ] of “Level,”
the HPF or LPF level.
Setting contents:
-12 to 0 dB (Initial setting: 0)
6
Repeat steps 2 to 5 to mak
other channels.
7
To store the adjusted setting value, t
hold [Preset 1], [Preset 2], or [Pr
least 2 seconds.
• Touch [
Flat
] to initialise all values.
• If the Rear Speaker setting is [ Off ], the Rear Speak
cannot be edited (page 29).
• If the Subwoofer setting is [
Off
], the Subwoofer setting cannot
be edited (page 29).
• While adjusting the X-OVER you should consider the
frequency response of the connected speakers.
Calling the X-Over adjusted value
Calling the pre-set X-OVER adjusted value.
Touch [Preset 1], [Preset 2], or [Preset 3].
The setting stored in the Preset will be recalled.
Setting the "bass engine"
You can set your favorite "bass engine" Type.
Setting contents:
Type: Off (Initial setting) / Standard / midbass
/ Rich / Lowbass / Punch
Level: 0 to 6
1
Touch [bass engine].
The "bass engine" setting screen is displayed.
2
Touch [bass engine] to switch the type.
Off Standard midbass Rich Lowbass
Punch Off
3
Touch [ ] or [ ] of “BASS ENGINE Level,” and
then adjust the level.
•
When the Defeat setting is [ On ], you cannot perform the bass
engine.
• The “bass engine” setting screen is returned to the Sound
Setup Menu screen if no operation has been performed for
more than 3 seconds.
Adjusting Bass Level/Treble Level
Setting item:
Bass, Treble
Setting contents:
Bass: -18 to 18 (Initial setting: 00)
Treble: -18 to 18 (Initial setting: 00)
Touch [ ] or [ ] of the “Bass” or “Treble,” to
adjust the level.
• The Bass level and Treble level are reflected in the settings of
Band2 and Band11 in EQ Setting. Depending on settings of
Band2 and Band11 in EQ Setting, the adjustable Bass level
and Treble level are changed.
• When “Bass” and “Treble” are not displayed, touch [ Subw. ] to
switch to [ Tone Adjust ] mode.
• Not available when “bass engine” is set.
Setting the Subwoofer
Touch [Tone Adjust].
The "Subwoofer Level" setting screen is displayed.
Adjusting the Subwoofer Level
You can set the Subwoofer level when a Subwoofer is
connected.
Setting item:
Subwoofer Level
Setting contents:
0 to 15 (Initial setting: 0)
Slide the lever left or right to adjust the level.
• This setting is only available when “Subwoofer” is set to [ On ]
(page 29).
Setting the Subwoofer Phase
The subwoofer output phase is toggled Subwoofer
Normal (0°) or Subwoofer Reverse (180°).
Setting item:
Phase
Setting contents:
0° (Initial setting) / 180°
Touch [Phase] to switch the subwoofer output
phase.
• This setting is only available when “Subwoofer” is set to [ On ]
(page 29).
Defeat Setting
If Defeat is [
On
], Media Xpander, EQ Setting and
"bass engine" functions are turned Off. This disables any
settings made for these functions.
Setting item:
Defeat
Touch [Defeat].
The indicator lights up when Defeat is set to On.