27
-EN
ALPINE DVA-9965R 68-02065Z31-A (EN)
Adjusting and Storing the Crossover
Settings
Before performing the following procedures, refer to “About the
Crossover” (page 26).
1
Press and hold
MENU
for at least 2 seconds.
2
Select the Crossover mode by sliding your finger
on the
GlideTouch bar
to the left or right. Press
the
GlideTouch bar
under the Crossover mode.
2 WAY System
3
Press
BAND
to select the band to be adjusted.
SUBW
→
REAR
→
FRONT
→
SUBW
4
Select the desired cut-off frequency (Crossover
Point) by sliding your finger on the
GlideTouch
bar
to the left or right.
Adjustable frequency bands: 20Hz to 200Hz
(in 1/3 octave steps)
5
Press
SOURCE/POWER
to adjust the slope.
Adjustable slope: FLAT, 6dB/oct., 12dB/oct.,
18dB/oct., 24dB/oct.
6
Adjust the output level by turning the
Rotary
encoder
.
Adjustable output level: -12 to 0 dB.
7
To adjust another band, repeat steps 3 to 6, then
adjust all bands.
8
When the setting has been completed, press
FUNC.
or the
GlideTouch bar
to activate the
preset mode.
9
Select any one of the preset numbers (1 through 6)
by sliding your finger on the
GlideTouch bar
to
the left or right. Press and hold the
GlideTouch
bar
under the desired preset for at least 2 seconds.
The adjustments are saved in the selected preset.
10
After setting, press and hold
MENU
for at least 2
seconds to return to normal mode.
• If
MENU
is pressed while adjusting or setting items in the MENU
mode, the unit returns to the previous selection screen.
• By pressing the
GlideTouch bar
under RETURN in the MENU
mode, the unit returns to the normal mode.
• If no operation is performed for 60 seconds, the unit returns to
normal mode.
3 WAY System
3
Press
BAND
to select the band to be adjusted.
LOW
→
MID-L
→
MID-H
→
HIGH
→
LOW
4
Select the desired cut-off frequency (Crossover
Point) by sliding your finger on the
GlideTouch
bar
to the left or right.
Adjustable frequency bands:
LOW
: 20Hz to 200Hz (in 1/3 octave steps)
MID-L
*
1
: 20Hz to 200Hz (in 1/3 octave steps)
MID-H
*
2
: 1kHz to 20kHz (in 1/3 octave steps)
HIGH
: 1kHz to 20kHz (in 1/3 octave steps)
*
1
: Midrange high-pass filter is adjusted.
*
2
: Midrange low-pass filter is adjusted.
5
Press
SOURCE/POWER
to adjust the slope.
Adjustable slope: FLAT
*
, 6dB/oct., 12dB/oct.,
18dB/oct., 24dB/oct.
*
FLAT can be set for the HIGH slope only when USER'S
is selected in “Setting the Response Slope for the High
Range Speaker (TW SETUP)” (page 39). Depending on
the response characteristics of the speaker, care should
be taken when setting the response slope to FLAT, as
speaker damage may result. With the DVA-9965R, a
message is displayed when the response slope for the
high range speaker is set to FLAT. After the message is
displayed, press the
Rotary encoder
to set to FLAT.
6
Adjust the output level by turning the
Rotary
encoder
.
Adjustable output level: -12 to 0 dB.
7
To adjust another band, repeat steps 3 to 6, then
adjust all bands.
8
When the setting has been completed, press
FUNC.
or the
GlideTouch bar
to activate the
preset mode.
9
Select any one of the preset numbers (1 through 6)
by sliding your finger on the
GlideTouch bar
to
the left or right. Press and hold the
GlideTouch
bar
under the desired preset for at least 2 seconds.
The adjustments are saved in the selected preset.
10
After setting, press and hold
MENU
for at least 2
seconds to return to normal mode.
• If
MENU
is pressed while adjusting or setting the items in the
MENU mode, the unit returns to the previous selection screen.
• By pressing the
GlideTouch bar
under RETURN in the MENU
mode, the unit returns to the normal mode.
• If no operation is performed for 60 seconds, the unit returns to
normal mode.
• About the 2way/3way system
You can switch to 2way/3way system mode with the 2way/3way
switch on the bottom side of the unit (page 68, 69 and 71).
When setting to “3 WAY”:
The unit can be operated in a 3 way system.
When setting to “F/R/Sub-W”:
The unit can be operated in a 2 way system.
F/R/Sub-W
3WAY
Содержание DVA-9965R
Страница 76: ......
