33
-EN
01GB05CDA105E.fm
ALPINE CDA-105E 68-09359Z81-A (EN)
• The iPhone/iPod is not connected.
- Make sure the iPhone/iPod is correctly connected (refer to
“Connections” on page 37).
Make sure the cable is not bent excessively.
• There are no songs in the iPhone/iPod.
- Download songs to the iPhone/iPod and connect to this unit.
• Communication error.
- Turn the ignition key off, and then set to ON again.
- Reset the iPod.
- Check the display by reconnecting between the iPhone/iPod
and this unit, using the iPhone/iPod cable.
• Caused by the iPhone/iPod Software Version not being
compatible with this unit.
- Update the iPhone/iPod Software Version to be compatible
with this unit.
• The iPhone/iPod is not verified.
- Change another iPhone/iPod.
• Abnormal current is run to the USB connector device.
- You can solve the problem by switching the source, turning the
unit power off, or ACC to the OFF position.
• A USB device that is not supported by the unit is connected.
- Connect a USB device that is supported by the unit.
• Malfunction occurred as a result of the speaker cable shorting on
the car chassis.
- Route the cable correctly, and set POWER IC to ON (page 16).
If the above solution does not work, consult your nearest
dealer.
Specifications
FM TUNER SECTION
AM TUNER SECTION
CD PLAYER SECTION
USB SECTION
* Frequency response may differ depending on the encoder
software/bit rate.
PICKUP
GENERAL
CHASSIS SIZE
NOSEPIECE SIZE
•
Due to continuous product improvement, specifications and design
are subject to change without notice.
Indication for iPod Mode
Indication for all Modes
Tuning Range
87.5-108.0 MHz
Mono Usable Sensitivity
9.3 dBf (0.8 µV/75 ohms)
50 dB Quieting Sensitivity
13.5 dBf (1.3 µV/75 ohms)
Alternate Channel Selectivity
80 dB
Signal-to-Noise Ratio
65 dB
Stereo Separation
35 dB
Capture Ratio
2.0 dB
Tuning Range
531-1,602 kHz
Sensitivity (IEC Standard)
22.5 µV/27 dB
Frequency Response
5-20,000 Hz (±1 dB)
Wow & Flutter (% WRMS)
Below measurable limits
Total Harmonic Distortion
0.008% (at 1 kHz)
Dynamic Range
95 dB (at 1 kHz)
Signal-to-Noise Ratio
105 dB
Channel Separation
85 dB (at 1 kHz)
USB requirements
USB 1.1/2.0
Max. Power Consumption
500 mA
USB Class
Mass Storage
File System
FAT 12/16/32
MP3 Decoding
MPEG-1/2 AUDIO Layer-3
WMA Decoding
Windows Media™ Audio
AAC Decoding
AAC-LC format “.m4a” file
Number of Channels
2-Channel (Stereo)
Frequency Response*
5-20,000 Hz (±1 dB)
Total Harmonic Distortion
0.008% (at 1 kHz)
Dynamic Range
95 dB (at 1 kHz)
Signal-to-Noise Ratio
105 dB
Channel Separation
85 dB (at 1 kHz)
Wave length
795 nm
Laser power
CLASS I
Power Requirement
14.4 V DC
(11-16 V allowable)
Maximum Power Output
50 W × 4
Maximum Pre-Output Voltage
2 V/10 k ohms
Bass
±14 dB at 100 Hz
Treble
±14 dB at 10 kHz
Weight
1.5 kg (3 lbs. 4 oz)
Width
178 mm (7)
Height
50 mm (2")
Depth
160 mm (6-1/4")
Width
170 mm (6-3/4")
Height
46 mm (1-13/16")
Depth
24 mm (15/16")
01GB00CDA105E.book Page 33 Thursday, November 6, 2008 2:22 PM
