manualshive.com logo in svg

alphatronics AlphaCom XL, Руководство по обслуживанию

Поделиться
Скачать
alphatronics AlphaCom XL Скачать руководство пользователя страница 41

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 41/74 

Settings Serial port 2 

 
The second serial port can also be used for various applications including the transparent serial connection 
over IP.  
 
 
Serial port 2 can be also be used to connect a serial logprinter from various types of control panels (for 
instance Galaxy and Thor). In this way, many control panels can be connected serially to the AlphaCom XL. 
Establishing a serial connection can be performed by following actions: 
 

 

connect a serial cable between a control panel serial logprinter output and RS-232 port2 (see 

page 18 

and 19

 for details) 

 

set the function / protocol of RS-232 port 2 to „Galaxy‟ (Universal logprinter protocol) 

 

enable event logging at the control panel to the logprinter 

 
Every event, that is received from the logprinter, will be transmitted transparently to the control station using 
the SIA-HS over IP data protocol. An event can be transmitted if the „logline‟ from the printer port of the 
control panel ends with a <LF> character (line-feed, ASCII character with hexadecimal value 0x0a). Each 
logline should also contain a time indication (e.g. 12:30). When a logline is received at the AlphaCom XL, it 
is checked to contain a colon (:) and at the left and right side of that column 2 digits. If the mentioned 
requirements are met, then the logline will be transmitted to the control station. If not, then the received 
information will be dropped without notice. 
 
Take care: some control panels need to activate the logprinter option via a function on the keypad before 
events will be transmitted serially. In that case always check if the logprinter function works after a restart of 
the control panel. 
 
The way the above mentioned application works is stated in a separate document and can be obtained from 
the Alphatronics helpdesk. 
 
 

Settings Serial port 3 

 
The third serial port is a RS-485 bus. In the default settings this function is „disabled‟. By programming this 
port to „

AlphaVision

‟ and connecting it to the RS-485 bus of the AlphaVision control panel the AlphaCom 

XL will be seen as a AlphaCom ISDN or AlphaCom IP device on the RS-485 bus with the exception that 
there is no up/download capabilities.  
 
When the AlphaCom XL is connected to the RS-485 bus of the AlphaVision control panel, the following 
settings must also be made: 
 
 

Содержание AlphaCom XL











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды