Alpha Pro Tec 115 Скачать руководство пользователя страница 36

Страница: 36 / 48

Alpha Pro Tec - Programming the Boiler PCB

The boiler is supplied with the PCB configuration set according to the boiler model, however it is possible to adjust certain

parameters according to the boiler and system configuration.

Note:

These parameters should only be adjusted by an approved Alpha engineer or Agent.

To access the programming menu, press and hold buttons 'B'

and

'C'

simultaneously. The screen will display the letter P and a corresponding

parameter number and then display the corresponding set value for that

parameter. Scroll through the parameters by using the CH + and – buttons

('1' as shown in Fig. 9.1). To change a parameter value press the DHW +

and – buttons ('2' as shown in Fig. 9.11) to the desired value.
The parameter value is stored by either moving to the next parameter or by

pressing button 'B'.
Exit the parameter menu saving your new settings by pressing the buttons

'B'

and

'C' simultaneously. The boiler will then run a self-diagnostics cycle

displaying PARA and Auto on the screen.

Note:

After approximately 2 minutes the boiler will automatically exit this

menu without saving any changes and running a self-diagnostics cycle displaying PARA and Auto on the screen.

RESET

Fig. 9.1

9 PROGRAMMING THE BOILER PCB

Parameter

Feature

Description

100

Pro Tec 50 = 50
Pro Tec 70 = 70
Pro Tech 90 = 90
Pro Tec 115 = 115

Set CH flow temp.

Set max. flow temp.

Heating hysteresis (cycling)

Anti cycling time

Stabalisation period

CH ramp up time

Post circulation

Max. heat power output

Min. heat power output

Min. pump flow rate

Anti humidity setting

Not used

Boiler power value

External sensor setting

External sensor offset

DHW set temp.

Not used

DHW reheat temp.

DHW overrun cycle

Max. DHW output power

Min. DHW ouput power

P01

P02

P03

P04

P05

P06

P07

P08

P09

P10

P11

P12

P13

P14

P15

P16

P17

P18

P19

P20

P21

Adjustment

Default value

CH flow temp. range.

Max. flow temp.

Flow temp. differential between cycling.

Time delay between firing to avoid boiler cycling.

Initial stabalisation period at min. rate.

Time to ramp up the CH flow temp. (0 is no ramp up).

Overrun time after CH set temp. is achieved.

Output power according to max. available.

Min. output setting.

Min. flow rate to activate the boiler.

Note:

Do not adjust this

parameter.

Fan speed setting for anti heat exchanger humidity cycle (0 =

disabled, recommended value = 40.

Boiler power information value - software setting for boiler type.

External sensor operating gradient, 0 is disabled.

CH offset in relation to external sensor gradient P14.

Set temp. for DHW when using boiler DHW function.

Temp. differential to reheat DHW function from P16.

Overrun time after DHW set temp. is achieved.

Max. power available during DHW function.

Min. power available during DHW function.

20 - P02 °C

20 - 95°C

2 - 10°C

0 - 15 mins

3 - 10 mins

0 - 60°C

1 - 30 mins

P09 - 10%

0 - P08%

5 - 47 l/min

P26 - 120 RPM x 50

0 - 255 kW

0 - 10

20 - 70°C

20 - 65°C

2 - 10°C

0 - 180 sec

P21 - 100%

0 - P20%

Parameter Programming Menu

Содержание Pro Tec 115

















































Результаты поиска

Содержание Pro Tec 115

Отзывы:

Alpha Pro Tec 115, Инструкции по установке и обслуживанию, Страница: 36 / 48

Результаты поиска

Содержание Pro Tec 115

Отзывы: