Alpes Lasers ECLK Скачать руководство пользователя страница 8

Страница: 8 / 41

2 Notation

The use of DANGER, WARNING and CAUTION notation in this manual is in compli-
ance with the SEMI standard S-13-0298

; their definition is given below. They may

also be used to alert against unsafe practices.

DANGER:

Indicates an

immediate

hazardous situation, which, if not avoided,

may result in death or serious injury.

WARNING:

Indicates a

potentially

hazardous situation, which, if not avoided,

may result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided,

may result in minor or moderate injury or property damage.

The use of IMPORTANT and

Note

notations is defined below.

IMPORTANT:

Contains instructions or practices associated with maintenance and operation

of the Starter Kit. Highlights specific actions or steps to be followed in order to

avoid defeating equipment functionality or cause product damage.

Note

: contains instructions or practices associated with maintaining the Starter Kit.

Clarifies issues needing the reader’s attention.

SEMI S13-0298:

Safety Guidelines for Operation and Maintenance Manuals Used with Semicon-

ductor Manufacturing Equipment

, Semiconductor Equipment and Materials International (Moun-

tainview, CA) 1998

viii

ECLK user’s manual v1.0.6

Содержание ECLK










































Результаты поиска

Содержание ECLK

Отзывы:

Бренды по названию

Популярные бренды

Alpes Lasers ECLK, Руководство пользователя

Результаты поиска

Содержание ECLK

Отзывы:

Бренды по названию

Популярные бренды