background image

Read this entire manual through to the end before proceeding with the assembly.

Bridgeport | Braxton

 Installation & Owner’s Manual

Note: While there are cosmetic and feature differences between the Bridgeport and the Braxton, the models 

assemble the same except where noted.

Thank you for your purchase of your 

Bridgeport | Braxton

 

sauna! Should you have any questions during 

assembly, please feel free to call us at 888.355.3050, or email [email protected]. Regular business 

hours are 9-5 EST, M-F.

Your Bridgeport | Braxton Indoor Sauna is specifically designed to utilize your existing floor. As such, 

assembly is made very simple since the entire sauna sits on pre-fabricated rails and risers rather than on 

floor platform. Your sauna can be assembled on any surface that is firm and flat, including concrete, ceramic, 

vinyl, laminate or tile. Installation on a carpeted surface is not recommended. If you prefer a wood floor 

inside your sauna, please visit our website at 

almostheaven.com

 to investigate our red cedar floor kits!

Your Bridgeport | Braxton kit should include the following:

BRIDGEPORT | BRAXTON  SAUNA INSTALLATION MANUAL

page 1

These tools are required to assemble your Bridgeport | Braxton sauna:

c

  Cordless drill

c

  Tape measurer

c

  Rubber mallet

c

  Hammer

c

  1/2” or 5/8” Forstner Bit

c

  Utility Knife

c

  Screwdriver (Phillips and Flathead)

c

  Level

c

  Step stool or ladder

c

  Framing square

c

  4 floor risers

4 Wall Support Rails

4 Roof Support Rails

3 Roof Sections

Wall Section A

Wall Section B

Wall Section C

Wall Section D

Wall Section E

Wall Section F

Window Section G

Door Section H

Window Section I

Wall Section J

Upper Bench

Extra Upper Bench Support

Lower Long Bench

Lower Long Bench Vertical Support

Lower Side Bench

3 Lower Side Bench Supports

Long Backrest w/LED light

Short Backrest

LED Power Supply

Doorknob Assembly

Bucket and Ladle

Heater

Stones

Thermometer/Hydrometer

Wall Sensor Cover

Hardware Bag containing 

       2” screws, 2.5” Bench Screws, and Trim nails

Heater Fence Kit

Содержание Bridgeport









Отзывы: