background image

RC3-LOG & RC3P-LOG INSTRUCTION MANUAL 

 

 

Page 

8

 

 

SHAWALMEX-EUROPE BV

 

 

 RC3-LOG & RC3P-LOG INSTRUCTION MANUAL SEPT 2018 

 
 

 

 

 

RAISE/LOWER  BUTTONS 

Within  trending  displays, the  Raise  and Lower  keys  can  be used to  scroll  through the  enabled 
display modes in the  sequence: vertical  trend, horizontal trend, vertical  bargraph,  horizontal 
bargraph,  numeric, vertical trend... and so  on. 

Within  configuration pages,  these  pushbuttons  act  as  cursor keys,  allowing, for  example, the 
user  to  high- light  menu items for selection using the  scroll  button, and in many  cases allowing 
the  user  to  select one from a number of alternative values within  menu items.  Theses keys  are 
also  used to  navigate through the  virtual keyboards and number pads used to  enter text  or 
numeric strings. 

5.1.1.  Setting the Process Values  

1.

 

Starting at the home screen the following screens can be seen by pushing the page button and the lower 
button: 

 

2.

 

Figure 5: Process Overview screen.  
The setpoints of Upper and Lower Platen and the dwelltime can be adjusted in this screen. 
 

 

3.

 

Figure 6: Channel “cycling” screen 
By default, the recorder scrolls through all the channels (Top platen, Bottom platen, Pressure and 
Temperature Probe)  in the display group, with each channel becoming the active channel in turn. 
 
 

Содержание RC3-LOG
















Отзывы: