manualshive.com logo in svg

Allworx Px 6/2, Руководство по установке, Страница: 14 / 23

Поделиться
Скачать
Allworx Px 6/2 Скачать руководство пользователя страница 14

 

Px 6/2 Expander Installation Guide 

 

300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com 

© 2008 Allworx. All rights reserved 

Version 03. Revised: May 16, 2008 

 

Page 11 

 
6.  Verify that the PC has an IP address on the 192.168.2.xxx network. 
 

You may need to release and renew the PC’s IP address using the ipconfig command in a command 
window to get an address from the Port Expander. 

 
7.  Open a web browser on the PC and enter 

http://192.168.2.254

 into the browser’s address field. 

 

The Port Expander’s Configuration screen is displayed. 

8.  Scroll to the New Password field. Enter the site’s new Port Expander administrator password. Re-enter the 

password in the Confirm Password field. 

 
9. Click 

Update 

 

The Port Expander’s Update Result screen is displayed. 

10. Disconnect the network cable from the Port Expander’s Network port. Connect the Port Expander to the 

system using the procedure in either Section 7.2, Local Connection or Section 7.3, Remote Connection. 

 
11. Save the password for future reference. If the password is lost or forgotten, it can be reset by repeating this 

procedure and entering a new password. 

 

 

7.2 Local Connection 

When properly connected to the server LAN, the Allworx Px 6/2 will be configured automatically. This should 
require no manual steps, although it is recommended that the password be set in accordance with the 
procedure, above. To ensure the automatic configuration is successful, perform the following steps: 
 
1.  If the Port Expander has already been powered on, disconnect power. 
 
2.  Connect the Network port of the Port Expander to the LAN of the Allworx server per the diagram above 

using a standard RJ-45 category 5 Ethernet cable. 

 
3.  Apply power to the Port Expander. 
 
4.  Observe the Power LED. During power up, it will flash green. When the LED stops flashing and shines 

solid green, the Port Expander has received any software updates and has been configured. This may take 
as long as five (5) minutes. It is now ready for CO lines and analog phones to be connected to its FXO and 
FXS ports. 

 
5.  If the Power LED does not shine solid green within five (5) minutes. Unplug and re-plug the Port 

Expander’s power adapter.  

 
6.  Activate the FXO and FXS ports through the Web Admin page on the Allworx Server. Refer to the Allworx 

System Administrator’s Guide, Release 6.9

 or higher for information on configuring the ports. 

 

Содержание Px 6/2
























Отзывы:

Нет отзывов