background image

I N S T A L L A T I O N   A N D   O W N E R ’ S   M A N U A L

 

As of date of manufacture, 

meets all ANSI/UL 325 Safety 

Requirements for Vehicular 

Garage Door Openers 

Residential Vehicular Garage Door Opener 

Model MVP-SB  SUPER BELT 

R E A D   T H I S   M A N U A L   C A R E F U L L Y   B E F O R E   I N S T A L L A T I O N   O R   U S E  

104334 

INSTALLER:  Place this manual in the plastic envelope provided and 

permanently attach to the wall near the pushbutton.

 

Product Features ................................................... 2 
Component Identification .....................................  3 
Identify Your Door Type ........................................ 3 
Important Installation Instructions........................ 4 
Assembly Instructions........................................... 5 
Installing the Opener ............................................. 7 
  Mounting the Front Bracket ................................ 7 
  Mounting the Power Head ................................... 7 
 Power Requirements/Permanent Wiring ............ 8 
Control and Auxiliary Equipment.......................... 9 
  Installation of the Super Station ......................... 9 
  Standard Wall Push Button Installation ............. 9 
  Installation of Safe Finish Photosystem........... 10 
 Important Safety Instructions ........................... 11 
Installation Checklist ........................................... 12 

 TABLE OF CONTENTS 

WARNING

 

Indicates a 

MECHANICAL 

hazard of INJURY 

OR DEATH. Gives 

instructions to avoid 

the hazard

Operation and Adjustment Instructions..............12 
  Basic Operating Parameters..............................12 
  Door Arm Connection ........................................13 
  Programming The Radio System ......................14 
  FCC and IC Radio Operation Statement  ..........15 
  Testing the Limit Settings..................................16 
 Testing the Sensitivity .......................................16 
  Testing the Reversing System ..........................16 
  Testing the Safe Finish Photosystem ...............17 
  Operating the Super Station ..............................17 
Wiring Diagram.....................................................18 
Using the Manual Release Mechanism ...............19 
Troubleshooting Guide ........................................19 
Warranty Statement..............................................20 

CAUTION

 

 

 

READ THESE STATEMENTS CAREFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY 

The Warning and Caution boxes throughout this manual are there to protect you and your equipment.  

Pay close attention to these boxes as you follow the manual.

 

WARNING

 

CAUTION

 

Indicates an ELECTRICAL 

hazard of DAMAGE to the 

door, door opener, or 

equipment.  Gives 

instructions to avoid the 

hazard

Indicates an 

ELECTRICAL hazard 

of INJURY OR 
DEATH. Gives 

instructions to avoid 

the hazard

Indicates a MECHANICAL 

hazard of DAMAGE to the 

door, door opener, or 

equipment.  Gives 

instructions to avoid the 

hazard

 

 

By

 

Содержание SUPER BELT MVP-SB





















Отзывы: