AllSportSystems SUPERBAY Скачать руководство пользователя страница 32

Страница: 32 / 47

All

SportSystems, Inc.

2019.

(1) Wrap the ShotDefender™
cabling around the upper depth
poles, approximately 6” in front
of the screen.

(2) Open turn turnbuckle as far
as possible without coming
apart. Attach hook end of the
turnbuckle to the other end of
the cable.

(3) If there is too much slack in
the cable, lossen wire clip nuts
on one end of the cable. Pull
slack out of the cable and
retighen wire clips. Cut extra
cable or use cable ties to hold
in place

(4) Tighten the cable by twisting
the turnbuckle causing the
cable to shorten. It should
have good tension.

(5) Attach the white velcro
sleeve valance to the cable.
Valance is same color and
fabric as your screen.

(6) Insert 1 inch PVC piping into
the sleeve to provide extra
weight to the sleeve. Balls
directed to the shot defender
will be deflected.

Page 32 of 47

Return to Table of Contents

Rev June 6, 2019

Содержание SUPERBAY
















































Результаты поиска

Содержание SUPERBAY

Отзывы:

Похожие инструкции для SUPERBAY

Бренды по названию

Популярные бренды

AllSportSystems SUPERBAY, Руководство по установке

Результаты поиска

Содержание SUPERBAY

Отзывы:

Похожие инструкции для SUPERBAY

Бренды по названию

Популярные бренды