Allnet ALL6800 Скачать руководство пользователя страница 46

Страница: 46 / 118

Link Aggregation

(ALL6800 only)

Specifies whether WAN and LAN ports will be aggregated and

act as one port.
Failover: When one port fails, the other one will take over.

Load Balance: Ethernet traffic will flow alternative between two

Ethernet ports.

802.3ad: Linkage two Ethernet ports in parallel to increase
throughput.

LAN Configuration

The ALL6800 supports two Gigabit
Ethernet ports for higher service

availability. To configure these
ports, choose LAN from the
Network menu, and the LAN

Configuration screen appears.
Press Apply to save your changes.

LAN Configuration

Item Description
MAC Address

Displays the MAC address of the LAN interface.

Specifies the IP address of the LAN interface.

Netmask

Specifies the Network Mask of the LAN interface.

Jumbo Frame Support

Enable or disable Jumbo Frame Support on the LAN interface.

NOTE

• Only use Jumbo Frame settings when operating in a Gigabit

environment where all other clients have Jumbo Frame Setting

enabled.

• Enabling DHCP automatically turns on UPnP— see the Service

Support Screen.

• If you are only using the WAN port, we suggest that you disable IP

Sharing Mode. This will result in higher throughput.

• A correct DNS setting is vital to networks services, such as SMTP

and NTP.

• To use the Link Aggregation with “802.3ad selected” feature,

please make sure the networking equipment on the other end of

Ethernet cable also supports 802.3ad protocol.

WARNING

Most Fast Ethernet (10/100) Switches/Routers do not support Jumbo

Frame and you will not be able to connect to your ALL6800 after

Jumbo Frame is turned on. If this happens, turn off the ALL6800. Then,

power on the ALL6800 and immediately press and hold the Reset

button on the back of the unit for 10 seconds. This will reset your

network settings, password, and turn off Jumbo Frame Support.

NOTE

Before enabling Jumbo Frame Support, please make sure your network

equipment supports Jumbo Frame. If your equipment is incompatible,

you might not be able to connect to your ALL6800. In this case, you

have to reset the system back to default by the holding down front

panel reset button for 5 seconds during boot up process.

Содержание ALL6800























































































































Результаты поиска

Содержание ALL6800

Отзывы:

Бренды по названию

Популярные бренды

Allnet ALL6800, Руководство пользователя

Результаты поиска

Содержание ALL6800

Отзывы:

Бренды по названию

Популярные бренды