28
!
NOTE:
By lightly depressing the pedals forward and reverse, torque is developed to be
transferred to the drive wheels by the hydraulic motor and differential set-up.
The further the forward and reverse pedals are depressed, the faster ground speed.
Torque will decrease as ground speed increases.
3. Move the forward / reverse pedal to the neutral position to stop.
NOTE:
The pedal returns to a neutral position when pressure is released from the
forward and reverse pedals.
LOADER CONTROL VALVE LEVER
The loader control valve returns to the neutral position when
released, except when in the float position.
A -
Move the control valve lever
forward
to
lower
loader arms.
AA -
Move the control valve lever
forward
past the detent. This is
the
float
position.
B -
Move the control valve lever
back
to
raise
the loader arms.
C -
Move the control valve lever
left
to
roll back
the bucket.
D -
Move the control valve lever
right
to
dump
the bucket.
For faster loader cycle times follow these simple tips:
1. Run engine at fast idle.
2. Move the loader boom and the bucket at the same time.
3. Without using force,
move control valve lever fully toward each function.
OPERATING TIPS
Reduce speed when
driving over rough terrain, carrying heavy loads, or working in a con-
gested area.
Whenever possible, avoid obstacles, such as rough terrain, rocks, curbs and ditches.
In general, by decreasing machine speed the control of the machine increases.
When the backhoe is not in use, the backhoe boom must be locked in the fully raised posi-
tion. Curl the backhoe bucket up and retract dipperstick.
When driving the
Allmand TLB
, carry the loader bucket low for good visibility and machine
stability.
Walk the job site to uncover any hazards and to plan the job.
Practicing good housekeeping on the job site will help maximize machine stability, reduce
operator fatigue, and increase productivity.
Material that is loose and fragmented dumps much easier than material that is hard and
compacted.
Excavate material in thin layers rather than jamming it into the bucket. This will allow the mate-
rial to break up as it enters the bucket. This is especially important when moving sticky, wet
materials.
CAUTION!
PREVENT POSSIBLE INJURY FROM UNEX-
PECTED MACHINE MOVEMENT, OPERATE
THE LOADER ONLY WHEN YOU ARE IN THE
OPERATOR’S SEAT FACING FORWARD.
Not
for
Reproduction
Содержание TLB 220
